Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0472752 AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for V35A-FTS)  P17029F  AT Solenoids Operation Shutdown Circuit Stuck Off  


DESCRIPTION

The TCM detects a malfunction in the current cut circuit used to transition to a fail-safe gear position.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P17029F AT Solenoids Operation Shutdown Circuit Stuck Off Once 5 seconds elapse after the vehicle is parked and the ignition switch is turned off, any of the following conditions is continuously met for 0.1 seconds or more during a solenoid current cut request (1 trip detection logic).
·

Solenoid (SL1) valve actual current value is 0.3 A or higher

·

Solenoid (SL2) valve actual current value is 0.3 A or higher

·

Solenoid (SL3) valve actual current value is 0.3 A or higher

·

Solenoid (SL4) valve actual current value is 0.3 A or higher

·

Solenoid (SL5) valve actual current value is 0.3 A or higher

·

Solenoid (SL6) valve actual current value is 0.3 A or higher

·

Solenoid (SLT) valve actual current value is 0.3 A or higher

·

Solenoid (SLU) valve actual current value is 0.3 A or higher

·

Solenoid (SC1) valve is ON

·

Solenoid (SL) valve is ON

·

Solenoid (SR) valve is ON


·

Wire harness or connector

·

TCM power source circuit

·

Transmission revolution sensor (NT)

·

Transmission revolution sensor (SP2)

·

Transmission wire

·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SLT) valve

·

Solenoid (SLU) valve

·

Solenoid (SC1) valve

·

Solenoid (SL) valve

·

Solenoid (SR) valve

·

TCM


Does not come on DTC stored SAE: P1702

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnostic Condition When a solenoid current cut request is sent after 5 seconds elapse after the vehicle is parked and the ignition switch is turned off ○ ○ ○ ○ ○ ○
Malfunction Condition Solenoid (SL1) valve actual current value is 0.3 A or higher ○ - - - - -
Solenoid (SL2) valve actual current value is 0.3 A or higher - ○ - - - -
Solenoid (SL3) valve actual current value is 0.3 A or higher - - ○ - - -
Solenoid (SL4) valve actual current value is 0.3 A or higher - - - ○ - -
Solenoid (SL5) valve actual current value is 0.3 A or higher - - - - ○ -
Solenoid (SL6) valve actual current value is 0.3 A or higher - - - - - ○
Duration 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 7 Pattern 8 Pattern 9 Pattern 10 Pattern 11
Diagnostic Condition When a solenoid current cut request is sent after 5 seconds elapse after the vehicle is parked and the ignition switch is turned off ○ ○ ○ ○ ○
Malfunction Condition Solenoid (SLT) valve actual current value is 0.3 A or higher ○ - - - -
Solenoid (SLU) valve actual current value is 0.3 A or higher - ○ - - -
Solenoid (SC1) valve is ON - - ○ - -
Solenoid (SL) valve is ON - - - ○ -
Solenoid (SR) valve is ON - - - - ○
Duration 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more 0.1 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is stored when any of the above detection patterns are met.


MONITOR DESCRIPTION

When the ignition switch is off and current is detected as flowing to the solenoid valve during a solenoid current cut request, the TCM stores a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P17029F.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C457472E02
1.323,0.625 1.938,0.823 0.615,0.198 10 false SL1+ 2.458,0.625 3.073,0.823 0.615,0.198 10 false SL1+ 1.323,1.573 1.938,1.771 0.615,0.198 10 false SL1- 2.448,1.573 3.063,1.771 0.615,0.198 10 false SL1- 5.563,1.573 6.177,1.771 0.615,0.198 10 false SL2- 4.417,1.573 5.031,1.771 0.615,0.198 10 false SL2- 4.417,0.625 5.031,0.823 0.615,0.198 10 false SL2+ 5.542,0.625 6.156,0.823 0.615,0.198 10 false SL2+ 1.323,2.698 1.938,2.896 0.615,0.198 10 false SL3+ 2.458,2.688 3.073,2.885 0.615,0.198 10 false SL3+ 1.313,3.635 1.927,3.833 0.615,0.198 10 false SL3- 2.458,3.635 3.073,3.833 0.615,0.198 10 false SL3- 4.417,2.698 5.031,2.896 0.615,0.198 10 false SL4+ 5.542,2.698 6.156,2.896 0.615,0.198 10 false SL4+ 4.406,3.646 5.021,3.844 0.615,0.198 10 false SL4- 5.552,3.635 6.167,3.833 0.615,0.198 10 false SL4- 1.313,4.656 1.927,4.854 0.615,0.198 10 false SL5+ 2.448,4.656 3.063,4.854 0.615,0.198 10 false SL5+ 1.302,5.594 1.917,5.792 0.615,0.198 10 false SL5- 2.448,5.594 3.063,5.792 0.615,0.198 10 false SL5- 4.406,5.594 5.021,5.792 0.615,0.198 10 false SL6- 5.563,5.594 6.177,5.792 0.615,0.198 10 false SL6- 4.417,4.646 5.031,4.844 0.615,0.198 10 false SL6+ 5.552,4.646 6.167,4.844 0.615,0.198 10 false SL6+ 1.313,6.615 1.927,6.813 0.615,0.198 10 false SLT+ 2.469,6.615 3.083,6.813 0.615,0.198 10 false SLT+ 1.292,7.552 1.906,7.75 0.615,0.198 10 false SLT- 2.448,7.552 3.063,7.75 0.615,0.198 10 false SLT- 4.406,7.552 5.021,7.75 0.615,0.198 10 false SLU- 5.573,7.552 6.188,7.75 0.615,0.198 10 false SLU- 4.417,6.615 5.031,6.813 0.615,0.198 10 false SLU+ 5.573,6.615 6.188,6.813 0.615,0.198 10 false SLU+ 2.24,0.625 2.396,0.823 0.156,0.198 10 false 6 1.76,0.625 2.073,0.823 0.313,0.198 10 false 23 1.75,1.573 2.063,1.771 0.313,0.198 10 false 24 2.167,1.573 2.479,1.771 0.313,0.198 10 false 25 1.771,2.698 2.083,2.896 0.313,0.198 10 false 13 2.208,2.688 2.365,2.885 0.156,0.198 10 false 7 1.76,3.635 2.073,3.833 0.313,0.198 10 false 14 2.188,3.635 2.5,3.833 0.313,0.198 10 false 26 1.771,4.656 2.083,4.854 0.313,0.198 10 false 11 2.24,4.656 2.552,4.854 0.313,0.198 10 false 3 1.75,5.594 2.063,5.792 0.313,0.198 10 false 12 2.167,5.594 2.479,5.792 0.313,0.198 10 false 22 1.771,6.615 2.083,6.813 0.313,0.198 10 false 27 2.156,6.615 2.469,6.813 0.313,0.198 10 false 10 1.75,7.552 2.063,7.75 0.313,0.198 10 false 28 2.156,7.552 2.469,7.75 0.313,0.198 10 false 29 4.865,0.625 5.177,0.823 0.313,0.198 10 false 5 5.271,0.625 5.583,0.823 0.313,0.198 10 false 19 4.854,1.573 5.167,1.771 0.313,0.198 10 false 24 5.271,1.573 5.583,1.771 0.313,0.198 10 false 20 4.854,2.698 5.167,2.896 0.313,0.198 10 false 8 5.271,2.698 5.583,2.896 0.313,0.198 10 false 15 4.844,3.646 5.156,3.844 0.313,0.198 10 false 27 5.26,3.635 5.573,3.833 0.313,0.198 10 false 16 4.865,4.646 5.177,4.844 0.313,0.198 10 false 9 5.26,4.646 5.573,4.844 0.313,0.198 10 false 25 4.865,5.594 5.177,5.792 0.313,0.198 10 false 28 5.26,5.594 5.573,5.792 0.313,0.198 10 false 26 4.875,6.615 5.188,6.813 0.313,0.198 10 false 4 5.25,6.615 5.563,6.813 0.313,0.198 10 false 17 4.865,7.552 5.177,7.75 0.313,0.198 10 false 23 5.271,7.563 5.583,7.76 0.313,0.198 10 false 18 0.531,1.146 1.458,1.479 0.927,0.333 10 false Solenoid (SL1) Valve 5.708,1.094 6.625,1.438 0.917,0.344 10 false Solenoid (SL2) Valve 0.552,3.208 1.479,3.542 0.927,0.333 10 false Solenoid (SL3) Valve 5.708,3.167 6.625,3.5 0.917,0.333 10 false Solenoid (SL4) Valve 0.531,5.177 1.479,5.521 0.948,0.344 10 false Solenoid (SL5) Valve 5.719,5.125 6.656,5.49 0.938,0.365 10 false Solenoid (SL6) Valve 0.552,7.073 1.479,7.427 0.927,0.354 10 false Solenoid (SLT) Valve 5.719,7.063 6.667,7.406 0.948,0.344 10 false Solenoid (SLU) Valve 0.167,8.333 0.479,8.531 0.313,0.198 10 false C33 0.167,8.5 2,8.698 1.833,0.198 10 false Transmission Wire 5.583,8.333 5.896,8.531 0.313,0.198 10 false C33 5.583,8.5 7.042,8.729 1.458,0.229 10 false Transmission Wire 3.271,8.333 3.729,8.531 0.458,0.198 10 false C36 3.281,8.5 4.115,8.74 0.833,0.24 10 false TCM 3.083,0.302 3.698,0.5 0.615,0.198 10 false 12 V 3.083,2.375 3.698,2.573 0.615,0.198 10 false 12 V 3.083,4.333 3.698,4.531 0.615,0.198 10 false 12 V 3.083,6.292 3.698,6.49 0.615,0.198 10 false 12 V 4.333,6.292 4.948,6.49 0.615,0.198 10 false 12 V 4.333,4.333 4.948,4.531 0.615,0.198 10 false 12 V 4.354,0.302 4.969,0.5 0.615,0.198 10 false 12 V 4.354,2.365 4.969,2.563 0.615,0.198 10 false 12 V 0.156,0.813 0.313,1.01 0.156,0.198 10 false 1 6.927,0.813 7.083,1.01 0.156,0.198 10 false 1 6.927,2.885 7.083,3.083 0.156,0.198 10 false 1 0.156,2.875 0.313,3.073 0.156,0.198 10 false 1 0.156,4.844 0.313,5.042 0.156,0.198 10 false 1 6.927,4.833 7.083,5.031 0.156,0.198 10 false 1 6.927,6.802 7.083,7 0.156,0.198 10 false 1 0.167,6.802 0.323,7 0.156,0.198 10 false 1 0.156,1.615 0.313,1.813 0.156,0.198 10 false 2 0.156,3.688 0.313,3.885 0.156,0.198 10 false 2 0.156,5.656 0.313,5.854 0.156,0.198 10 false 2 0.167,7.625 0.323,7.823 0.156,0.198 10 false 2 6.927,7.604 7.083,7.802 0.156,0.198 10 false 2 6.927,5.667 7.083,5.865 0.156,0.198 10 false 2 6.927,3.708 7.083,3.906 0.156,0.198 10 false 2 6.927,1.625 7.083,1.823 0.156,0.198 10 false 2

C457473E02
1.365,0.792 1.823,0.99 0.458,0.198 10 false NTB 2.448,0.792 2.906,0.99 0.458,0.198 10 false NTB 1.344,2.021 1.802,2.219 0.458,0.198 10 false NTO 2.469,2.021 2.927,2.219 0.458,0.198 10 false NTO 1.76,0.792 2.073,0.99 0.313,0.198 10 false 21 1.76,2.021 2.073,2.219 0.313,0.198 10 false 22 5.552,0.792 6.167,0.99 0.615,0.198 10 false SP2B 4.417,0.792 5.031,0.99 0.615,0.198 10 false SP2B 5.531,2.021 6.146,2.219 0.615,0.198 10 false SP2O 4.417,2.021 5.031,2.219 0.615,0.198 10 false SP2O 1.448,2.979 1.76,3.177 0.313,0.198 10 false SL 2.479,2.979 2.792,3.177 0.313,0.198 10 false SL 4.573,2.979 4.885,3.177 0.313,0.198 10 false SR 5.552,2.979 5.865,3.177 0.313,0.198 10 false SR 2.448,4.438 2.906,4.635 0.458,0.198 10 false SC1 1.365,4.438 1.823,4.635 0.458,0.198 10 false SC1 1.76,4.438 1.917,4.635 0.156,0.198 10 false 7 1.771,2.979 1.927,3.177 0.156,0.198 10 false 5 5.323,2.979 5.479,3.177 0.156,0.198 10 false 6 5.24,0.792 5.552,0.99 0.313,0.198 10 false 29 5.26,2.021 5.573,2.219 0.313,0.198 10 false 30 2.156,2.969 2.469,3.167 0.313,0.198 10 false 44 4.896,2.979 5.208,3.177 0.313,0.198 10 false 45 2.146,4.438 2.458,4.635 0.313,0.198 10 false 46 4.865,0.792 5.177,0.99 0.313,0.198 10 false 12 4.875,2.021 5.188,2.219 0.313,0.198 10 false 31 0.146,1.938 0.302,2.135 0.156,0.198 10 false 1 6.938,1.938 7.094,2.135 0.156,0.198 10 false 1 0.135,1.115 0.292,1.313 0.156,0.198 10 false 2 6.927,1.115 7.083,1.313 0.156,0.198 10 false 2 5.771,1.313 6.635,2.052 0.865,0.74 10 false Transmission Revolution Sensor (SP2) 0.552,1.323 1.417,2.01 0.865,0.688 10 false Transmission Revolution Sensor (NT) 5.729,3.448 6.594,3.906 0.865,0.458 10 false Solenoid (SR) Valve 0.563,4.948 1.531,5.406 0.969,0.458 10 false Solenoid (SC1) Valve 0.583,3.51 1.469,3.938 0.885,0.427 10 false Solenoid (SL) Valve 3.375,5.813 4.344,6.198 0.969,0.385 10 false TCM 3.073,6.458 4.906,6.656 1.833,0.198 10 false Transmission Wire 2.75,6.458 3.208,6.656 0.458,0.198 10 false C33 3.375,5.635 3.833,5.833 0.458,0.198 10 false C36 2.167,0.792 2.479,0.99 0.313,0.198 10 false 30 2.167,2.021 2.479,2.219 0.313,0.198 10 false 11 3.094,0.5 3.552,0.698 0.458,0.198 10 false 12V 4.385,0.469 4.844,0.667 0.458,0.198 10 false 12V 3.042,2.729 3.5,2.927 0.458,0.198 10 false 12V 4.427,2.729 4.885,2.927 0.458,0.198 10 false 12V 3.021,4.188 3.479,4.385 0.458,0.198 10 false 12V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm
NT Sensor Voltage NT sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Idling -
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPEED (SP2) AND SP2 SENSOR VOLTAGE)

B

12.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)
2.READ VALUE USING GTS (SPEED (SP2) AND SP2 SENSOR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped
(Output shaft speed is equal to vehicle speed)
-
SP2 Sensor Voltage SP2 sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Idling -
Powertrain > Transmission > Data List
Tester Display
Speed (SP2)
SP2 Sensor Voltage
50003 373 362,391

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID VALVE) - TCM)

B

8.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID VALVE) - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-6 (SL1+) - C36-25 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C36-5 (SL2+) - C36-24 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C36-7 (SL3+) - C36-26 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
C36-8 (SL4+) - C36-27 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
C36-3 (SL5+) - C36-22 (SL5-) 20°C (68°F) 5.0 to 5.6 Ω
C36-9 (SL6+) - C36-28 (SL6-) 20°C (68°F) 5.0 to 5.6 Ω
C36-10 (SLT+) - C36-29 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C36-4 (SLU+) - C36-23 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C36-44 (SL) - Body ground 20°C (68°F) 11 to 15 Ω
C36-45 (SR) - Body ground 20°C (68°F) 11 to 15 Ω
C36-46 (SC1) - Body ground 20°C (68°F) 11 to 15 Ω
C36-6 (SL1+) or C36-25 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
C36-5 (SL2+) or C36-24 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (SL3+) or C36-26 (SL3-) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (SL4+) or C36-27 (SL4-) - Body ground and other terminals Always 10 kΩ or higher
C36-3 (SL5+) or C36-22 (SL5-) - Body ground and other terminals Always 10 kΩ or higher
C36-9 (SL6+) or C36-28 (SL6-) - Body ground and other terminals Always 10 kΩ or higher
C36-10 (SLT+) or C36-29 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (SLU+) or C36-23 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TCM POWER SOURCE CIRCUIT

NG

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
4.CHECK TCM POWER SOURCE CIRCUIT

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>TCM Power Source Circuit

HINT:

Check the TCM power source circuit, and proceed to the next step if no malfunction is recognized.


Result:
Proceed to
NEXT



NEXT

5.REPLACE TCM
6.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33,C36)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C33-23 (SL1+) - C36-6 (SL1+) Always Below 1 Ω
C33-24 (SL1-) - C36-25 (SL1-) Always Below 1 Ω
C33-19 (SL2+) - C36-5 (SL2+) Always Below 1 Ω
C33-20 (SL2-) - C36-24 (SL2-) Always Below 1 Ω
C33-13 (SL3+) - C36-7 (SL3+) Always Below 1 Ω
C33-14 (SL3-) - C36-26 (SL3-) Always Below 1 Ω
C33-15 (SL4+) - C36-8 (SL4+) Always Below 1 Ω
C33-16 (SL4-) - C36-27 (SL4-) Always Below 1 Ω
C33-11 (SL5+) - C36-3 (SL5+) Always Below 1 Ω
C33-12 (SL5-) - C36-22 (SL5-) Always Below 1 Ω
C33-25 (SL6+) - C36-9 (SL6+) Always Below 1 Ω
C33-26 (SL6-) - C36-28 (SL6-) Always Below 1 Ω
C33-27 (SLT+) - C36-10 (SLT+) Always Below 1 Ω
C33-28 (SLT-) - C36-29 (SLT-) Always Below 1 Ω
C33-17 (SLU+) - C36-4 (SLU+) Always Below 1 Ω
C33-18 (SLU-) - C36-23 (SLU-) Always Below 1 Ω
C33-5 (SL) - C36-44 (SL) Always Below 1 Ω
C33-6 (SR) - C36-45 (SR) Always Below 1 Ω
C33-7 (SC1) - C36-46 (SC1) Always Below 1 Ω
C33-23 (SL1+) or C36-6 (SL1+) - Body ground and other terminals Always 10 kΩ or higher
C33-24 (SL1-) or C36-25 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
C33-19 (SL2+) or C36-5 (SL2+) - Body ground and other terminals Always 10 kΩ or higher
C33-20 (SL2-) or C36-24 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
C33-13 (SL3+) or C36-7 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
C33-14 (SL3-) or C36-26 (SL3-) - Body ground and other terminals Always 10 kΩ or higher
C33-15 (SL4+) or C36-8 (SL4+) - Body ground and other terminals Always 10 kΩ or higher
C33-16 (SL4-) or C36-27 (SL4-) - Body ground and other terminals Always 10 kΩ or higher
C33-11 (SL5+) or C36-3 (SL5+) - Body ground and other terminals Always 10 kΩ or higher
C33-12 (SL5-) or C36-22 (SL5-) - Body ground and other terminals Always 10 kΩ or higher
C33-25 (SL6+) or C36-9 (SL6+) - Body ground and other terminals Always 10 kΩ or higher
C33-26 (SL6-) or C36-28 (SL6-) - Body ground and other terminals Always 10 kΩ or higher
C33-27 (SLT+) or C36-10 (SLT+) - Body ground and other terminals Always 10 kΩ or higher
C33-28 (SLT-) or C36-29 (SLT-) - Body ground and other terminals Always 10 kΩ or higher
C33-17 (SLU+) or C36-4 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C33-18 (SLU-) or C36-23 (SLU-) - Body ground and other terminals Always 10 kΩ or higher
C33-5 (SL) or C36-44 (SL) - Body ground and other terminals Always 10 kΩ or higher
C33-6 (SR) or C36-45 (SR) - Body ground and other terminals Always 10 kΩ or higher
C33-7 (SC1) or C36-46 (SC1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SL), (SR) AND (SC1) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SL), (SR) AND (SC1) VALVE

OK

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLT), (SLU), (SL), (SR) OR (SC1) VALVE

8.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
a.

Disconnect the transmission wire connector.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

9.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))

NG

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
9.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))
a.
C377609C09
0.094,2.219 0.5,2.479 0.406,0.26 1.667,3 1.313,2.531 true 0.906,3.01 1.188,2.531 true 2.25,1.344 1.896,0.875 true 1.385,1.344 1.667,0.865 true 0.104,0.26 0.417,0.458 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 1.563,3.042 2.021,3.24 0.458,0.198 10 false SP2B 0.75,3.042 1.208,3.24 0.458,0.198 10 false SP2O 2.25,1.406 2.708,1.604 0.458,0.198 10 false 1 1.323,1.406 1.781,1.604 0.458,0.198 10 false 2 0.188,2.292 0.5,2.49 0.313,0.198 10 false C33
*a Front view of wire harness connector
(to Transmission Revolution Sensor (SP2))
*b Component without harness connected
(Transmission Wire)


Disconnect the transmission revolution sensor (SP2) connector.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Terminal 2 of the transmission revolution sensor (SP2) connector - C33-29 (SP2B) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (SP2) connector - C33-30 (SP2O) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (SP2) connector or C33-29 (SP2B) - Body ground Always 10 kΩ or higher
Terminal 1 of the transmission revolution sensor (SP2) connector or C33-30 (SP2O) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

NG

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

11.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)
a.

Disconnect the transmission wire connector.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

13.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))

NG

14.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
13.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))
a.
C377609C10
0.104,2.208 0.5,2.51 0.396,0.302 2.563,3 2.208,2.531 true 1.813,3.01 2.094,2.531 true 2.25,1.344 1.896,0.875 true 1.385,1.344 1.667,0.865 true 0.104,0.26 0.417,0.458 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 2.448,3.063 2.906,3.26 0.458,0.198 10 false NTB 1.667,3.063 2.125,3.26 0.458,0.198 10 false NTO 2.25,1.406 2.708,1.604 0.458,0.198 10 false 1 1.323,1.406 1.781,1.604 0.458,0.198 10 false 2 0.198,2.292 0.51,2.49 0.313,0.198 10 false C33
*a Front view of wire harness connector
(to Transmission Revolution Sensor (NT))
*b Component without harness connected
(Transmission Wire)


Disconnect the transmission revolution sensor (NT) connector.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Terminal 2 of the transmission revolution sensor (NT) connector - C33-21 (NTB) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (NT) connector - C33-22 (NTO) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (NT) connector or C33-21 (NTB) - Body ground Always 10 kΩ or higher
Terminal 1 of the transmission revolution sensor (NT) connector or C33-22 (NTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

NG

14.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

15.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR