Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C13807F  Stop Lamp Relay Actuator Stuck Off  


DESCRIPTION

Refer to DTC C13807E.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C13807E

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
C13807F Stop Lamp Relay Actuator Stuck Off Either of the following is detected:
·

When the IG1 terminal voltage exceeds 10 V and the +BS terminal voltage is from 9.5 to 17.4 V, stop light drive output (STPO) is ON, STP is OFF and STP2 is OFF continuously for 2 seconds or more.

·

When the IG1 terminal voltage exceeds 10 V and the +BS terminal voltage is from 9.5 to 17.4 V, STP is OFF and STP2 is ON continuously for 5 seconds or more.


·

Wire harness and connector

·

Stop light switch assembly

·

STP circuit

·

STP2 circuit

·

No. 2 skid control ECU (brake actuator assembly)


Brake/EPB Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY



PROCEDURE

1.CHECK DTC
a.

Check the DTCs that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only C13807F is output A
C13807F and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Perform the stop light control relay (stop light switch assembly) Active Test, and confirm that the stop lights illuminate and turn off and the value of "Stop Light SW", "Stop Light Relay" and "STPO" changes.

Chassis > Brake/EPB > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Stop Lamp Relay Stop light control relay (Stop light switch assembly) OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON
Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Stop Light Relay Stop light control relay (Stop light switch assembly) status
(STP terminal input)
OFF / ON OFF: Stop light control relay (Stop light switch assembly) off and brake pedal released
ON: Stop light control relay (Stop light switch assembly) on or brake pedal depressed
HINT:

The voltage of power supplied to the stop lights is measured at the STP terminal.


STPO Stop light control relay (Stop light switch assembly) status
(STPO terminal output)
OFF / ON OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on)
HINT:

When STPO is ON, the stop light control relay (stop light switch assembly) turns ON and the stop lights illuminate


Chassis > Brake/EPB > Active Test
Active Test Display
Stop Lamp Relay
Data List Display
Stop Light SW
Stop Light Relay
STPO
50004 435 27 59,67,252

Result:
Data List Status Stop Light Illumination Status Proceed to
Stop Light SW Stop Light Relay STPO
OFF OFF ON Not illuminated A
OFF OFF ON Illuminated B
ON ON ON Illuminated C



A

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

B

8.CHECK BRAKE ACTUATOR ASSEMBLY

C

9.CHECK BRAKE ACTUATOR ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-32 (STPO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK BRAKE ACTUATOR ASSEMBLY

NG

7.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
5.CHECK FOR SHORT TO GROUND IN STP CIRCUIT
a.

Check that there is no short to ground in the STP circuit (wire harnesses, connectors, stop lights and ECUs)

OK:

There is no short to ground.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE MALFUNCTIONING PART

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B43 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.




Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.
C440416C33
0.448,0.656 0.781,0.906 0.333,0.25 2.125,1.656 1.74,1.021 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.49,0.688 0.948,0.885 0.458,0.198 10 false B43 2.042,1.688 2.5,1.885 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B43)Location & Routing

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

B43-4 (ACC) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-11 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-37 (STP2) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

10.CHECK STOP LIGHT SWITCH ASSEMBLY
10.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the B43 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B20)Location & Routing

Click Connector(B20)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Skid Control ECU (Brake Actuator Assembly)

B20-37 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

11.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
11.CHECK FOR SHORT TO +B IN STP2 CIRCUIT
a.

Check that there is no short to +B in the STP2 circuit (wire harnesses, connectors and ECUs).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART