Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0469467 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Turn Assist Indicator Light Circuit  


DESCRIPTION

When any of the following conditions are met, the turn assist system becomes operable and the turn assist indicator light illuminates.

·

Crawl Control is operating.

·

The turn assist function switch is on.

·

Front differential and rear differential are free.

·

The vehicle is moving at a speed of 10 km/h (6 mph) or less.

·

The brake pedal is not operated.

·

The shift lever is not in P, R or N.

·

The steering angle is large.


WIRING DIAGRAM

C256733E29
4.604,2.531 7.031,3.031 2.427,0.5 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.604,2.354 4.958,2.604 0.354,0.25 10 false B19 2.625,1.792 2.979,1.979 0.354,0.188 10 false I85 2.625,1.958 4.385,2.281 1.76,0.323 10 false Turn Assist Function Switch (Transfer Position Switch) 0.24,2.563 2.167,2.917 1.927,0.354 10 false Combination Meter Assembly 5.344,1.51 5.813,1.688 0.469,0.177 10 false EXI4 5.104,1.396 5.281,1.583 0.177,0.188 10 false 5 4.094,1.396 4.521,1.583 0.427,0.188 10 false 2 2.844,1.406 3.219,1.583 0.375,0.177 10 false 1 0.542,3.26 2.521,3.542 1.979,0.281 10 false : CAN Communication System 3.729,1.396 4.052,1.604 0.323,0.208 10 false ECU 2.99,1.396 3.469,1.563 0.479,0.167 10 false GND2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>UTILITY


PROCEDURE

1.INSPECT TRANSFER POSITION SWITCH

OK

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - TRANSFER POSITION SWITCH)

NG

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - TRANSFER POSITION SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the I85 turn assist function switch (transfer position switch) connector.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXI4 CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (EXI4 CIRCUIT)
a.

Turn the ignition switch off.


b.

Connect the B19 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the I85 turn assist function switch (suspension control switch) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I85)Location & Routing

Click Connector(I85)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transfer Position Switch

I85-2 (ECU) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY