Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL LOCK POSITION SWITCH
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473043 REAR DIFFERENTIAL LOCK POSITION SWITCH A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL LOCK POSITION SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

C458433N01
2.167,4.25 2.75,4.25 true 6.313,0.198 6.896,0.198 true 1.333,1.167 1.333,1.417 1.333,1.417 1.083,1.417 true 6.083,3.917 6.083,4.917 6.083,4.917 5.5,4.917 true 3.167,0.5 2.833,0.5 2.833,0.5 2.833,1.583 true 5.167,2.167 4.833,2.167 4.833,2.167 4.667,2.25 true 1.333,1.75 1.083,1.75 1.083,1.75 1.083,2 true 3.333,2.333 3.333,2.833 3.333,2.833 3,2.833 true 5.5,3.583 5.5,4.083 5.5,4.083 5.167,4.083 true 2.802,4.094 3.438,4.417 0.635,0.323 18 false 1, 2 5.729,0.052 6.344,0.375 0.615,0.323 18 false 3, 4 0.792,1.24 1.094,1.573 0.302,0.333 18 false 5 3.656,0.344 3.958,0.677 0.302,0.333 18 false 6 5.156,4.75 5.458,5.083 0.302,0.333 18 false 6 5.552,2.01 5.854,2.344 0.302,0.333 18 false 7 1.542,1.594 1.844,1.927 0.302,0.333 18 false 8 2.719,2.719 3.031,2.917 0.313,0.198 10 false *1 4.885,4 5.198,4.198 0.313,0.198 10 false *1 3.5,1.396 3.958,1.594 0.458,0.198 10 false x 2 6.698,3.208 7.156,3.406 0.458,0.198 10 false x 2 1.385,1.646 1.583,1.854 0.198,0.208 10 false ● 0.552,1.25 0.75,1.458 0.198,0.208 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY 41110 - - -
2 SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY 41110 - - -
3 INSPECT DIFFERENTIAL RING GEAR BACKLASH - (Click here) - -
4 INSPECT TOTAL PRELOAD - - - -
5 REMOVE WIRING HARNESS CONNECTOR - - - -
6 REMOVE DIFFERENTIAL BEARING CAP 41303E (Click here) - -
7 REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY 84222Q (Click here) - -
8 REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH - - - -

*1 PLATE WASHER - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear differential lock position switch removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc.
w/ Parking Support Brake System:
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.



HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



CAUTION:
·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


Be sure to perform this procedure with several people as the rear differential carrier assembly is very heavy.

·

Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

Z101186

Click here(Click here)

Hide 6.REMOVE DIFFERENTIAL BEARING CAP

Z101186

Click here(Click here)

Hide 41303E 7.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 84222Q 8.REMOVE DIFFERENTIAL LOCK INDICATOR SWITCH

a.
C458434