The steering sensor receives the following switch information:
Light control switch in tail, head or AUTO position
Dimmer switch in high, low or high flash (pass) position
Fog light switch in front*1, rear*2 or off position
*1: w/ Front Fog Light
*2: w/ Rear Fog Light
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Auto Light Switch | Light control switch AUTO position signal | OFF or ON | OFF: Light control switch not in AUTO position ON: Light control switch in AUTO position |
- |
| Head Light Switch (Tail) | Light control switch tail position signal | OFF or ON | OFF: Light control switch not in tail position ON: Light control switch in tail position |
- |
| Head Light Switch (Head) | Light control switch head position signal | OFF or ON | OFF: Light control switch not in head position ON: Light control switch in head position |
- |
| High Beam Main Switch | Dimmer switch high position signal | OFF or ON | OFF: Dimmer switch not in high position ON: Dimmer switch in high position |
- |
| Passing Light Switch | Dimmer switch high flash position (pass) signal | OFF or ON | OFF: Dimmer switch not in high flash position ON: Dimmer switch in high flash position |
- |
| Front Fog Light Switch | Front fog light switch signal | OFF or ON | OFF: Front fog light switch off ON: Front fog light switch on |
w/ Front Fog Light |
| Rear Fog Light/Bad Weather Switch | Rear fog light switch signal | OFF or ON | OFF: Rear fog light switch off ON: Rear fog light switch on |
w/ Rear Fog Light |
| Tester Display |
|---|
| Auto Light Switch |
| Head Light Switch (Tail) |
| Head Light Switch (Head) |
| High Beam Main Switch |
| Passing Light Switch |
| Front Fog Light Switch |
| Rear Fog Light/Bad Weather Switch |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Light Control Switch (HEAD) | Light control switch head position signal | OFF or ON | OFF: Light control switch not in head position ON: Light control switch in head position |
- |
| Tester Display |
|---|
| Light Control Switch (HEAD) |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>PROBLEM SYMPTOMS TABLE
NG
| *a | Component without harness connected (Steering Sensor) |
- | - |
Remove the steering sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I51,z3)Location & Routingewd_type=routing;type=c,c;code=I51,z3 Click Connector(z3)Instrument Panel>other>Steering Wheel Switch Housing , Spiral Cable Sub-Assemblyewd_type=component;type=c;code=z3;pinno=4 |
||
| I51-7 (HEAD) - z3-4 (H) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I51,I3)Location & Routingewd_type=routing;type=c,c;code=I51,I3 |
||
| I51-7 (HEAD) - I3-26 (HEAD) | Always | Below 1 Ω |
| I51-7 (HEAD) or I3-26 (HEAD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG