Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Headlight ECU)
RM38G0E _59 Vehicle Exterior _100649 LIGHTING (EXT) _0468742 LIGHTING SYSTEM(w/o Headlight ECU) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Headlight ECU)  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

E466708E01
2.865,1.448 5.281,2.438 2.417,0.99 10 false Semiconductor Power Integration ECU 2.885,1.281 5.302,2.271 2.417,0.99 10 false B57 4.479,0.813 6.896,1.802 2.417,0.99 10 false 17 4.26,0.938 6.677,1.927 2.417,0.99 10 false L 2.604,3.198 5.021,4.188 2.417,0.99 10 false Fog Light LED LH 2.646,4.896 5.073,5.594 2.427,0.698 10 false Fog Light LED RH 0.76,5.292 3.208,5.729 2.448,0.438 10 false : CXPI Communication Line 5.5,1.542 6.635,3 1.135,1.458 10 false Power Distribution Box Assembly 2.594,4.729 5,5.677 2.406,0.948 10 false A2 2.542,3.031 4.958,4.021 2.417,0.99 10 false A1 4.063,2.583 6.479,3.573 2.417,0.99 10 false 1 4.063,4.281 6.479,5.271 2.417,0.99 10 false 1 4.073,2.24 6.49,3.229 2.417,0.99 10 false 2 4.063,3.948 6.479,4.938 2.417,0.99 10 false 2 3.781,3.938 6.198,4.927 2.417,0.99 10 false B 3.781,2.219 6.198,3.208 2.417,0.99 10 false B 3.771,2.552 6.188,3.542 2.417,0.99 10 false E 3.792,4.302 6.208,5.292 2.417,0.99 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.

Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Input Signal Front fog light power supply signal OFF or ON OFF: Front fog light is not input
ON: Front fog light is input
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Input Signal
50003 473 414
OK:

Display changes according to the front fog light switch operation.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Output Signal Front fog light output OFF or ON OFF: Front fog lights off
ON: Front fog lights on
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Output Signal
50003 473 415
OK:

Display changes according to the front fog light switch operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS

NG

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

3.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)

NG

6.READ VALUE USING GTS
4.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A1 fog light LED LH connector.


c.

Disconnect the A2 fog light LED RH connector.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A1,A2)Location & Routing

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A1-1 (E) - Body ground Always Below 1 Ω
A2-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS
a.

Disconnect the A1 fog light LED LH connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

7.READ VALUE USING GTS
7.READ VALUE USING GTS
a.

Reconnect the A1 fog light LED LH connector.


b.

Disconnect the A2 fog light LED RH connector.


c.

Read the Data List according to the display on the GTS.

Body Electrical > Power Integration No.1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Fog Light Fuse Shut Off Status Front Fog Light Fuse Shut Off Status OFF or ON OFF: Fuse not shut off
ON: Fuse shut off
-
Body Electrical > Power Integration No.1 > Data List
Tester Display
Front Fog Light Fuse Shut Off Status
50003 473 417
OK:

The Data List value displays "OFF".



Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
8.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR POWER INTEGRATION ECU - FOG LIGHT LED)
a.

Disconnect the B57 semiconductor power integration ECU connector.


b.

Disconnect the A1 fog light LED LH connector.


c.

Disconnect the A2 fog light LED RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B57,A1,A2)Location & Routing

Click Connector(B57)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Semiconductor Power Integration ECU

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

B57-17 (L) or A1-2 (B) - Other terminals and body ground Always 10 kΩ or higher
B57-17 (L) or A2-2 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FOG LIGHT LED - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A1,A2)Location & Routing

Click Connector(A1)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit LH

Click Connector(A2)Engine Compartment>No. 4 Engine Room Wire / Switch Wire>Fog Light Unit RH

A1-1 (E) - Other terminals and body ground Always Below 1 Ω
A2-1 (E) - Other terminals and body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR