The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
Click herePower Source / Network>NETWORKING>CXPI COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Input Signal | Taillight input | OFF or ON | OFF: Taillights off ON: Taillights on |
- |
| Tester Display |
|---|
| Tail Light Input Signal |
Display changes according to the taillight illumination condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Output Signal | Taillight output | OFF or ON | OFF: Taillights off ON: Taillights on |
- |
| Tester Display |
|---|
| Tail Light Output Signal |
Display changes according to the taillight illumination condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
Disconnect the 5J power distribution box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5J-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the c2 rear combination light cord LH connector.
Disconnect the b2 rear combination light cord RH connector.
Disconnect the g2 rear light socket and wire LH connector.
Disconnect the g1 rear light socket and wire RH connector.
Disconnect the g3 license plate light assembly with back door opener switch connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the c2 rear combination light cord LH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear combination light lens and body LH connector.
Connect the c2 rear combination light cord LH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b2 rear combination light cord RH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear combination light lens and body RH connector.
Connect the b2 rear combination light cord RH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g2 rear light socket and wire LH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear light lens and body LH connector.
Connect the g2 rear light socket and wire LH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g1 rear light socket and wire RH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the rear light lens and body RH connector.
Connect the g1 rear light socket and wire RH connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g3 license plate light assembly with back door opener switch connector.
Turn the light control switch to the tail position.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Tail Light Fuse Shut Off Status | Taillight fuse shut off status | OFF or ON | OFF: Fuse has no shut off history ON: Fuse has shut off history |
- |
| Tester Display |
|---|
| Tail Light Fuse Shut Off Status |
The Data List value displays "OFF".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the c2 rear combination light cord LH connector.
Disconnect the b2 rear combination light cord RH connector.
Disconnect the g2 rear light socket and wire LH connector.
Disconnect the g1 rear light socket and wire RH connector.
Disconnect the g3 license plate light assembly with back door opener switch connector.
Disconnect the 5F power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(c2,b2,g2,g3)Location & Routingewd_type=routing;type=c,c,c,c;code=c2,b2,g2,g3 Click Connector(c2)Body>No. 8 Floor Wire>Rear Combination Light Assembly LHewd_type=component;type=c;code=c2;pinno=7 Click Connector(b2)Body>No. 7 Floor Wire>Rear Combination Light Assembly RHewd_type=component;type=c;code=b2;pinno=7 Click Connector(g2)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>Rear Light Assembly LHewd_type=component;type=c;code=g2;pinno=6 Click Connector(g3)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>License Plate Light Assembly with Back Door Opener Switchewd_type=component;type=c;code=g3;pinno=2 |
||
| c2-7 (TL), b2-7 (TL), g2-6 (B), g1- (B), g3-2 (B) or 5F-30 - Body ground6 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG