Home › Suspension › SUSPENSION CONTROL › STABILIZER CONTROL VALVE (for Rear Side) › 2021.04–2021.07
RM38G0E _53 Suspension _100546 SUSPENSION CONTROL _0473916 STABILIZER CONTROL VALVE(for Rear Side) A

SUSPENSION CONTROL  STABILIZER CONTROL VALVE(for Rear Side)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C459199N01
6.615,0.25 6.865,0.25 false 6.615,0.646 6.865,0.646 false 6.625,1.083 6.823,1.083 false 3.917,2.667 3.917,3 3.917,3 4.167,3 false 6.448,0.125 6.698,0.458 0.25,0.333 18 false 1 6.448,0.531 6.698,0.865 0.25,0.333 18 false 3 6.438,0.948 6.688,1.281 0.25,0.333 18 false 2 4.229,2.875 4.479,3.208 0.25,0.333 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 DRAIN SUSPENSION FLUID - - (Click here) -
4 STEP SUB-ASSEMBLY LH - - - -

C458542N01
3.417,2.25 3.667,2.833 3.667,2.833 4.083,2.833 true 3.583,2.25 3.833,2.833 true 2.75,2.271 2.75,3.104 2.75,3.104 2.583,3.104 true 3.146,4.042 3.146,4.375 3.146,4.375 3.396,4.375 false 5,4.229 5.333,4.479 0.333,0.25 10 false x 3 2.396,2.969 2.677,3.323 0.281,0.354 18 false 5 4.385,2.688 4.667,3.042 0.281,0.354 18 false 5 3.781,4.271 4.063,4.625 0.281,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR STABILIZER CONTROL TUBE ASSEMBLY - (Click here) - -
6 STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY 48860D (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the stabilizer control with accumulator housing assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane tracing assist system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.DRAIN SUSPENSION FLUID

Z101186

Click here(Click here)

Hide 4.REMOVE STEP SUB-ASSEMBLY LH

Hide 5.DISCONNECT REAR STABILIZER CONTROL TUBE ASSEMBLY

a.
C458551N01
0.438,0.073 0.688,0.49 0.25,0.417 18 false i

i.

Using a union nut wrench, disconnect the rear stabilizer control tube assembly.

NOTICE:
·

Do not kink or damage the rear stabilizer control tube assembly.

·

Do not allow any foreign matter such as dirt or dust to enter the rear stabilizer control tube assembly from the connecting parts.





Hide 48860D 6.REMOVE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY

Z101186

NOTICE:
·

Be careful not to allow any suspension fluid to enter the connector.

·

Do not apply excessive force to the rear stabilizer control tube assembly .




a.
C458553