Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (for LSD)
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0473041 REAR DIFFERENTIAL CARRIER ASSEMBLY(for LSD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for LSD)  REASSEMBLY  


CAUTION / NOTICE / HINT

C459341N01
2.906,5.156 3.833,5.396 0.927,0.24 2.844,5.083 3.906,5.469 1.063,0.385 2.833,2.5 2.833,1.5 2.833,1.5 3,1.5 true 1.083,3.25 1.083,0.5 1.083,0.5 2.333,0.5 true 1.833,0.5 1.833,3.083 true 4.438,3.469 4.604,3.469 4.604,3.469 4.604,3.073 true 5.292,4.156 6.083,4.156 6.083,4.156 6.083,2.406 true 5.417,2.5 5.417,3.25 5.417,3.25 6.083,3.25 true 6.49,0.198 6.885,0.198 true 2.615,5.271 2.458,5.271 2.458,5.271 2.458,3.521 true 2.594,3.552 3.073,3.75 0.479,0.198 10 false x 12 4.135,3.344 4.469,3.677 0.333,0.333 18 false 1 2.771,0.375 3.073,0.708 0.302,0.333 18 false 2 4.938,4.031 5.219,4.344 0.281,0.313 18 false 2 6.208,0.021 6.49,0.375 0.281,0.354 18 false 3 3.063,1.385 3.375,1.615 0.313,0.229 10 false *1 2.958,5.188 3.854,5.385 0.896,0.198 8 false 137 (1397, 101) 2.646,5.177 2.844,5.396 0.198,0.219 10 false ★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSTALL DIFFERENTIAL RING GEAR - (Click here) - -
2 INSTALL REAR DIFFERENTIAL CASE BEARING 41301A (Click here) - -
3 INSPECT DIFFERENTIAL RING GEAR RUNOUT - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ★ Precoated part

C459342N01
4.365,2.625 5.198,2.844 0.833,0.219 5.792,3.833 6.625,4.052 0.833,0.219 4.292,2.552 5.26,2.917 0.969,0.365 5.729,3.76 6.698,4.125 0.969,0.365 1.448,2.74 1.844,2.979 0.396,0.24 3.833,0.823 4.781,2.385 4.781,2.385 4.99,2.385 true 4.354,0.594 5.167,1.594 5.167,1.594 5.375,1.594 true 2.594,0.188 3.292,0.188 3.292,0.188 3.292,0.688 true 2.365,1.094 2.188,1.958 2.188,1.958 2.031,1.958 true 2.896,0.969 3.49,2.104 3.49,2.104 3.698,2.104 true 1.052,2.844 1.052,1.271 1.052,1.271 1.302,1.271 true 6.396,4.833 6.802,5.292 6.802,5.292 6.656,5.292 true 2.677,4.094 2.49,4.094 2.49,4.094 2.333,4.573 true 2.813,4.875 2.896,5.302 2.896,5.302 3.052,5.302 true 3.24,3.927 3.052,3.927 3.052,3.927 3.229,4.375 true 4.24,4.51 4.24,5.146 4.24,5.146 4.5,5.146 true 5.563,3.438 5.375,3.438 5.375,3.438 5.302,3.646 true 3.792,3.146 4.542,3.146 true 4.26,3.5 4.479,3.5 true 5.458,4.604 5.677,4.604 true 2.094,0.646 2.208,0.646 2.208,0.646 2.031,0.938 true 4.156,2.917 4.156,2.719 4.156,2.719 4.365,2.719 true 6.635,3.938 6.76,3.938 6.76,3.938 6.76,4.365 true 6.656,0.208 6.875,0.208 true 1.063,2.854 1.427,2.854 true 2.25,2.76 2.406,2.958 0.156,0.198 10 false ● 1.5,1.875 1.677,2.094 0.177,0.219 10 false ● 4.396,2.656 5.25,2.844 0.854,0.188 8 false 113 (1152, 83) 5.823,3.865 6.677,4.052 0.854,0.188 8 false 113 (1152, 83) 6.833,4.281 7.156,4.5 0.323,0.219 10 false x 2 3.854,2.75 4.177,2.969 0.323,0.219 10 false x 2 2.406,2.708 3.26,3.021 0.854,0.313 18 false 13, 36 0.781,0.531 2.063,0.865 1.281,0.333 18 false 14, 32, 35 5.385,2.24 6.552,2.542 1.167,0.302 18 false 4, 21, 24 1.771,0.083 2.646,0.406 0.875,0.323 18 false 20, 26 3.729,1.917 4.573,2.25 0.844,0.333 18 false 15, 30 5.698,1.438 6.573,1.76 0.875,0.323 18 false 19, 25 5.458,1.469 5.635,1.688 0.177,0.219 10 false ● 1.656,1.823 2.094,2.156 0.438,0.333 18 false 31 4.75,0.052 6.688,0.375 1.938,0.323 18 true 7, 9 - 12, 33, 34 3.438,5.188 4.281,5.521 0.844,0.333 18 false 5, 23 4.844,4.979 5.719,5.292 0.875,0.313 18 false 18, 27 5.885,5.167 6.76,5.479 0.875,0.313 18 false 16, 29 2.719,3.979 3.042,4.198 0.323,0.219 10 false *1 4.521,3.396 4.844,3.615 0.323,0.219 10 false *2 5.198,4.5 5.521,4.719 0.323,0.219 10 false *2 3.792,3.792 4.49,4.125 0.698,0.333 18 false 6, 22 5.99,3.281 7.104,3.615 1.115,0.333 18 false 8, 17, 28 4.979,2.958 5.854,3.271 0.875,0.313 18 false 16, 29 1.51,2.771 1.969,2.969 0.458,0.198 10 false *T1 3.615,3.844 3.792,4.063 0.177,0.219 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

4 INSTALL REAR DRIVE PINION FRONT BEARING (OUTER) 41201B (Click here) - -
5 INSTALL REAR DRIVE PINION REAR BEARING (OUTER) 41201A (Click here) - -
6 INSTALL REAR DRIVE PINION REAR BEARING (INNER) 41201A (Click here) - -
7 ADJUST DIFFERENTIAL DRIVE PINION PRELOAD - (Click here) - -
8 INSTALL DIFFERENTIAL CASE ASSEMBLY - (Click here) - -
9 ADJUST DIFFERENTIAL RING GEAR BACKLASH - (Click here) - -
10 ADJUST SIDE BEARING PRELOAD - (Click here) - -
11 INSPECT TOTAL PRELOAD - - -
12 INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION - - - -
13 REMOVE REAR DRIVE PINION NUT 41204B (Click here) - -
14 REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR 41204 (Click here) - -
15 REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER 41214 - - -
16 REMOVE DIFFERENTIAL BEARING CAP - (Click here) - -
17 REMOVE DIFFERENTIAL CASE ASSEMBLY - (Click here) - -
18 REMOVE DIFFERENTIAL DRIVE PINION - (Click here) - -
19 REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER 41321 - - -
20 REMOVE REAR DRIVE PINION FRONT BEARING (INNER) 41201B (Click here) - -
21 REMOVE REAR DRIVE PINION FRONT BEARING (OUTER) 41201B - - -
22 REMOVE REAR DRIVE PINION REAR BEARING (INNER) 41201A (Click here) - -
23 INSTALL REAR DRIVE PINION REAR BEARING (OUTER) 41201A (Click here) - -
24 INSTALL REAR DRIVE PINION FRONT BEARING (OUTER) 41201B (Click here) - -
25 INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER 41231 - - -
26 INSTALL REAR DRIVE PINION FRONT BEARING (INNER) 41201B - - -
27 INSTALL DIFFERENTIAL DRIVE PINION - (Click here) - -
28 INSTALL DIFFERENTIAL CASE ASSEMBLY - (Click here) - -
29 INSTALL DIFFERENTIAL BEARING CAP - - - -
30 INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER 41214 - - -
31 INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL 41201C - - -
32 INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR 41204 (Click here) - -
33 INSPECT TOTAL PRELOAD - - -
34 INSPECT DIFFERENTIAL RING GEAR BACKLASH - (Click here) - -
35 INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY 41204 - - -
36 STAKE DRIVE PINION NUT - - - -

*1 ADJUST SHIM *2 PLATE WASHER
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
● Non-reusable part
V100135

MP grease
V100136

Hypoid gear oil LSD *T1 457 N*m (4660 kgf*cm, 337 ft.*lbf) or less

PROCEDURE

Hide 1.INSTALL DIFFERENTIAL RING GEAR

a.
C458431C01
4.75,1.333 3.229,1.333 true 4.5,1.333 4.5,1.406 4.5,1.406 3.219,1.406 true 4.802,1.25 5.115,1.406 0.313,0.156 10 false *a 0.104,0.073 0.865,0.479 0.76,0.406 18 false i - vi
*a Matchmark - -


i.

Clean the contact surfaces of the differential case and differential ring gear.


ii.

Heat the differential ring gear in boiling water that is approximately 100°C (212°F).


iii.

Carefully remove the differential ring gear from the boiling water.


iv.

After the moisture on the differential ring gear has completely evaporated, quickly align the matchmarks on the differential ring gear and differential case and install the differential ring gear to the differential case.


v.

After the ring gear cools down sufficiently, apply adhesive to the 12 bolts and Temporarily install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond1360K or equivalent



vi.

Diametrically tighten the 12 bolts uniformly in several passes.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)



Hide 41301A 2.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C458432N01
3.656,0.635 3.844,0.427 3.844,0.427 4.01,0.427 true 2.667,1.417 2.833,1.417 2.833,1.417 3.448,1.594 true 2.344,1.333 2.802,1.531 0.458,0.198 10 false SST 4.063,0.344 4.521,0.542 0.458,0.198 10 false SST 0.448,0.083 0.729,0.438 0.281,0.354 18 false i

i.

Using SST and a press, press the 2 rear differential case bearings onto the differential case.

SST
09950-70010  (09951-07150)
09950-60011  (09951-00560, 09951-00580)



Hide 3.INSPECT DIFFERENTIAL RING GEAR RUNOUT

a.
C458095C01
2,1.094 2.729,1.5 2.729,1.5 2.875,1.5 true 2.729,1.5 1.969,1.042 true 3.844,0.073 4.448,0.469 0.604,0.396 18 false iii, iv 6.5,1.26 6.813,1.458 0.313,0.198 10 false *b 0.115,0.083 0.719,0.479 0.604,0.396 18 false i, ii 2.938,1.396 3.25,1.594 0.313,0.198 10 true *a
*a Matchmark *b 108 mm (4.25 in.)


i.

Install the differential case on the differential carrier, and install the 2 plate washers so that there is no play in the bearing.


ii.

Align the matchmarks on the differential bearing cap and differential carrier and Install the 2 differential bearing caps with the 4 bolts.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)


iii.

Using a dial indicator, measure the runout of the differential ring gear.

Maximum runout:

0.05 mm (0.00197 in.)



iv.

Remove the 2 differential bearing caps, 2 plate washers and differential case assembly.



Hide 41201B 4.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)

a.
C458097C01
3.125,0.719 3.542,0.719 true 3.083,0.417 3.5,0.417 true 3.792,0.844 4.208,0.844 true 4.271,0.76 4.583,0.917 0.313,0.156 10 false *1 2.792,0.323 3.208,0.573 0.417,0.25 10 false SST 2.802,0.635 3.219,0.885 0.417,0.25 10 false SST 0.458,0.115 0.75,0.417 0.292,0.302 18 false i
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer) - -


i.

Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60012  (09316-00011, 09316-00031)



Hide 41201A 5.INSTALL REAR DRIVE PINION REAR BEARING (OUTER)

a.
C458098C01
2.938,0.458 3.438,0.458 true 2.885,1.125 3.385,1.125 true 3.781,1.229 4.281,1.229 true 2.708,1.479 2.885,1.479 2.885,1.479 3.375,1.271 true 2.396,1.396 2.708,1.552 0.313,0.156 10 false *2 2.573,1.042 2.979,1.292 0.406,0.25 10 false SST 2.625,0.365 3.031,0.615 0.406,0.25 10 false SST 0.458,0.115 0.74,0.469 0.281,0.354 18 false i 4.333,1.156 4.646,1.313 0.313,0.156 10 false *1
*1 Rear Drive Pinion Rear Tapered Roller Bearing (Outer) *2 Adjust Shim


i.

Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60012  (09316-00011)
09950-60021  (09951-00910)

HINT:

First, install an adjust shim that has the same thickness as the removed adjust shim. After checking the tooth contact pattern, replace the adjust shim with one of a different thickness if necessary.




Hide 41201A 6.INSTALL REAR DRIVE PINION REAR BEARING (INNER)

a.
C459314N01
3.833,0.917 4.667,0.917 true 3.833,1.417 4.25,1.417 4.25,1.417 4.25,0.917 true 2.177,0.104 2.521,0.438 0.344,0.333 18 false i 4.708,0.823 5.198,1.052 0.49,0.229 10 false SST

i.

Using SST and a press, press the rear drive pinion rear tapered roller bearing (inner) onto the differential drive pinion.

SST
09950-60011  (09951-00610)
09308-14010  



Hide 7.ADJUST DIFFERENTIAL DRIVE PINION PRELOAD

a.
C458100N01
2.563,0.615 2.917,0.615 true 3.01,2.865 2.698,2.635 2.698,2.635 3.042,2.677 true 2.604,1.26 2.958,1.26 true 2.313,2.552 2.771,2.75 0.458,0.198 10 false SST 2.198,0.531 2.656,0.729 0.458,0.198 10 false SST 0.458,0.094 0.74,0.448 0.281,0.354 18 false i 4.365,0.125 4.646,0.479 0.281,0.354 18 false ii 2.219,1.167 2.677,1.365 0.458,0.198 10 false SST

i.

Install the differential drive pinion, rear drive pinion front tapered roller bearing (inner).

SST
09316-60012  (09316-00011, 09316-00031)
09608-04031  

HINT:

Install the rear differential drive pinion bearing spacer and rear differential carrier oil seal after adjusting the gear contact pattern.



ii.

Install the rear differential drive pinion oil slinger.



b.
C458101C01
1.385,0.542 1.802,0.542 true 5.5,0.594 5.583,0.25 5.583,0.25 5.75,0.25 true 3.104,0.833 3.417,0.99 0.313,0.156 10 false *a 0.833,1.5 1.146,1.656 0.313,0.156 10 false *b 1.042,0.458 1.5,0.656 0.458,0.198 10 false SST 5.813,0.156 6.271,0.354 0.458,0.198 10 false SST 0.521,0.156 0.927,0.479 0.406,0.323 18 false i, ii 3.688,0.146 4.281,0.469 0.594,0.323 18 false iii, iv
*a Turn *b Hold


i.

Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



ii.

Adjust the drive pinion preload by tightening the drive pinion nut.


iii.

Using SST to hold the companion flange in place, slowly tighten the nut within the drive pinion preload adjustment range so that it reaches the specified drive pinion preload (at Starting).

SST
09330-00021  (09330-00030)

Limit torque value:

457 N*m (4660 kgf*cm, 337 ft.*lbf) or less


NOTICE:
·

As there is no spacer, tighten a little at a time. Be careful not to overtighten the nut.

·

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.




iv.

Using a torque wrench, measure the preload.

Standard Drive Pinion Preload (Starting Torque):
Bearing Preload
New bearing 0.75 to 2.02 N*m (8 to 20 kgf*cm, 7 to 17 in.*lbf)
Reused bearing 0.73 to 1.83 N*m (8 to 18 kgf*cm, 7 to 16 in.*lbf)


NOTICE:
·

For a more accurate measurement, rotate the bearing forward and backward several times before measuring.

·

Record the differential drive pinion preload for the total preload measurement.





Hide 8.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C459337N01
0.469,0.115 0.75,0.469 0.281,0.354 18 false i

i.

Place the 2 rear differential case bearings (outer) to their respective bearings.

HINT:

Make sure the right and left races are not interchanged.




Hide 9.ADJUST DIFFERENTIAL RING GEAR BACKLASH

a.
C459343N01
1.917,2.188 2.344,2.531 0.427,0.344 18 false iii 3.76,0.104 4.188,0.448 0.427,0.344 18 false ii 0.448,0.115 0.875,0.458 0.427,0.344 18 false i

i.

Install the plate washer to the RH side (teeth side).

NOTICE:

Make sure that the differential ring gear has backlash.



ii.

Using a dial indicator, while holding the companion flange, measure the ring gear backlash.

Standard backlash (reference):

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



iii.

Refer to the backlash when selecting a plate washer for the RH side (teeth side).



b.
C459344N01
0.167,0.104 0.75,0.438 0.583,0.333 18 false i, ii 4.021,0.104 4.604,0.438 0.583,0.333 18 false iii

i.

Select a plate washer for the LH side (back side) so that there is no gap between the rear differential case bearing (outer) and differential case.


ii.

Using a plastic-faced hammer, install the plate washer to the LH side (back side).


iii.

Using a dial indicator, adjust the ring gear backlash until it is within the specification.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


NOTICE:
·

There should be no clearance between the plate washer and case.

·

Make sure that there is ring gear backlash.



HINT:

If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.




Hide 10.ADJUST SIDE BEARING PRELOAD

a.
C458105N01
0.146,0.063 0.375,0.354 0.229,0.292 18 false i

i.

After adjusting the backlash of the differential ring gear, remove the plate washer from the LH side (back side).



b.
C459345N01
0.458,0.083 0.948,0.406 0.49,0.323 18 false i, ii 3.969,0.083 4.458,0.406 0.49,0.323 18 false iii

i.

Using a micrometer, measure the thickness of the plate washer.


ii.

Using the backlash as a reference, select a new washer that is 0.05 to 0.20 mm (0.00197 to 0.00787 in.) thicker than the removed plate washer and, using a plastic-faced hammer, tap it in so that it fits against the bearing.

HINT:

Select a plate washer which can be pressed in 2/3 of the full amount with your finger.



iii.

Recheck the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of the washers on both sides by an equal amount.

HINT:

An approximately 0.02 mm (0.000787 in.) change in each plate washer results in a 0.03 mm (0.00118 in.) change in the backlash.


Standard Washer LH (Back Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-59183 2.07 to 2.09 (0.0815 to 0.0822) 90564-59199 2.39 to 2.41 (0.0941 to 0.0948)
90564-59184 2.09 to 2.11 (0.0823 to 0.0830) 90564-59200 2.41 to 2.43 (0.0949 to 0.0956)
90564-59185 2.11 to 2.13 (0.0831 to 0.0838) 90564-59201 2.43 to 2.45 (0.0957 to 0.0964)
90564-59186 2.13 to 2.15 (0.0839 to 0.0846) 90564-59202 2.45 to 2.47 (0.0965 to 0.0972)
90564-59187 2.15 to 2.17 (0.0847 to 0.0854) 90564-59203 2.47 to 2.49 (0.0973 to 0.0980)
90564-59188 2.17 to 2.19 (0.0855 to 0.0862) 90564-59204 2.49 to 2.51 (0.0981 to 0.0988)
90564-59189 2.19 to 2.21 (0.0863 to 0.0870) 90564-59205 2.51 to 2.53 (0.0989 to 0.0996)
90564-59190 2.21 to 2.23 (0.0871 to 0.0877) 90564-59206 2.53 to 2.55 (0.0997 to 0.1003)
90564-59191 2.23 to 2.25 (0.0878 to 0.0885) 90564-59207 2.55 to 2.57 (0.1004 to 0.1011)
90564-59192 2.25 to 2.27 (0.0886 to 0.0893) 90564-59208 2.57 to 2.59 (0.1012 to 0.1019)
90564-59193 2.27 to 2.29 (0.0894 to 0.0901) 90564-59209 2.59 to 2.61 (0.1020 to 0.1027)
90564-59194 2.29 to 2.31 (0.0902 to 0.0909) 90564-59210 2.61 to 2.63 (0.1028 to 0.1035)
90564-59195 2.31 to 2.33 (0.0910 to 0.0917) 90564-59211 2.63 to 2.65 (0.1036 to 0.1043)
90564-59196 2.33 to 2.35 (0.0918 to 0.0925) 90564-59212 2.65 to 2.67 (0.1044 to 0.1051)
90564-59197 2.35 to 2.37 (0.0926 to 0.0933) 90564-59213 2.67 to 2.69 (0.1052 to 0.1059)
90564-59198 2.37 to 2.39 (0.0934 to 0.0940) - -


Standard Washer RH (Teeth Side):
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-59214 2.05 to 2.07 (0.0807 to 0.0814) 90564-59230 2.37 to 2.39 (0.0934 to 0.0940)
90564-59215 2.07 to 2.09 (0.0815 to 0.0822) 90564-59231 2.39 to 2.41 (0.0941 to 0.0948)
90564-59216 2.09 to 2.11 (0.0823 to 0.0830) 90564-59232 2.41 to 2.43 (0.0949 to 0.0956)
90564-59217 2.11 to 2.13 (0.0831 to 0.0838) 90564-59233 2.43 to 2.45 (0.0957 to 0.0964)
90564-59218 2.13 to 2.15 (0.0839 to 0.0846) 90564-59234 2.45 to 2.47 (0.0965 to 0.0972)
90564-59219 2.15 to 2.17 (0.0847 to 0.0854) 90564-59235 2.47 to 2.49 (0.0973 to 0.0980)
90564-59220 2.17 to 2.19 (0.0855 to 0.0862) 90564-59236 2.49 to 2.51 (0.0981 to 0.0988)
90564-59221 2.19 to 2.21 (0.0863 to 0.0870) 90564-59237 2.51 to 2.53 (0.0989 to 0.0996)
90564-59222 2.21 to 2.23 (0.0871 to 0.0877) 90564-59238 2.53 to 2.55 (0.0997 to 0.1003)
90564-59223 2.23 to 2.25 (0.0878 to 0.0885) 90564-59239 2.55 to 2.57 (0.1004 to 0.1011)
90564-59224 2.25 to 2.27 (0.0886 to 0.0893) 90564-59240 2.57 to 2.59 (0.1012 to 0.1019)
90564-59225 2.27 to 2.29 (0.0894 to 0.0901) 90564-59241 2.59 to 2.61 (0.1020 to 0.1027)
90564-59226 2.29 to 2.31 (0.0902 to 0.0909) 90564-59242 2.61 to 2.63 (0.1028 to 0.1035)
90564-59227 2.31 to 2.33 (0.0910 to 0.0917) 90564-59243 2.63 to 2.65 (0.1036 to 0.1043)
90564-59228 2.33 to 2.35 (0.0918 to 0.0925) 90564-59244 2.65 to 2.67 (0.1044 to 0.1051)
90564-59229 2.35 to 2.37 (0.0926 to 0.0933) 90564-59245 2.67 to 2.69 (0.1052 to 0.1059)




Hide 11.INSPECT TOTAL PRELOAD

a.
C458107N01
0.125,0.083 0.406,0.438 0.281,0.354 18 false i

i.

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard Total Preload (Starting Torque):
Reduction Ratio Bearing Preload
3.307 New bearing 0.98 to 2.57 N*m (10 to 27 kgf*cm, 9 to 22 in.*lbf)
Reused bearing 0.98 to 2.34 N*m (10 to 23 kgf*cm, 9 to 20 in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 12.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C459346N01
0.094,0.073 0.667,0.417 0.573,0.344 18 false i, ii

i.

Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.


ii.

Hold the companion flange firmly in place and rotate the differential ring gear in both directions.



b.
C222533C04
1.49,1.177 1.906,1.427 0.417,0.25 10 false *a 0.135,0.094 0.583,0.469 0.448,0.375 18 false i 3.115,0.708 3.51,0.948 0.396,0.24 10 false *b 5.146,0.708 5.521,0.948 0.375,0.24 10 false *c 4.417,1.531 4.99,1.917 0.573,0.385 10 false *d 3.167,2.531 3.677,2.865 0.51,0.333 10 false *e 5.198,2.552 5.573,2.865 0.375,0.313 10 false *f 4.479,3.354 4.896,3.771 0.417,0.417 10 false *g 2.469,4.51 3.052,4.833 0.583,0.323 10 false *B 3.208,5.104 3.615,5.406 0.406,0.302 10 false *h 5.198,5.115 5.5,5.365 0.302,0.25 10 false *i 3.198,7.042 3.604,7.406 0.406,0.365 10 false *j 5.167,7.052 5.656,7.427 0.49,0.375 10 false *k 4.49,5.969 4.958,6.333 0.469,0.365 10 false *d 4.469,7.906 4.906,8.396 0.438,0.49 10 false *g 2.448,0.333 2.833,0.542 0.385,0.208 10 false *A
*A Drive Side *B Coast Side
*a Proper Contact *b Toe Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear.
*e Heel Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear. *h Heel Contact
*i Flank Contact *j Toe Contact
*k Face Contact - -


i.

Inspect the tooth contact pattern.

If the teeth are not contacting properly, use the following chart to select a proper adjust shim.

C458109C01
1.917,1.167 2.333,1.167 true 3.417,1.313 3.5,1.479 3.5,1.479 3.667,1.479 true 1.708,1.073 2,1.333 0.292,0.26 10 false *1 3.719,1.385 4.01,1.573 0.292,0.188 10 false *2
*1 Adjust Shim *2 Rear Drive Pinion Rear Tapered Roller Bearing (Outer)


Standard Adjust Shim Thickness:
Part No. Thickness mm (in.) Part No. Thickness mm (in.)
90564-76019 1.71 to 1.73 (0.0674 to 0.0681) 90564-76031 1.95 to 1.97 (0.0768 to 0.0775)
90564-76020 1.73 to 1.75 (0.0682 to 0.0688) 90564-76032 1.97 to 1.99 (0.0776 to 0.0783)
90564-76021 1.75 to 1.77 (0.0689 to 0.0696) 90564-76033 1.99 to 2.01 (0.0784 to 0.0791)
90564-76022 1.77 to 1.79 (0.0697 to 0.0704) 90564-76034 2.01 to 2.03 (0.0792 to 0.0799)
90564-76023 1.79 to 1.81 (0.0705 to 0.0712) 90564-76035 2.03 to 2.05 (0.0780 to 0.0807)
90564-76024 1.81 to 1.83 (0.0713 to 0.0720) 90564-76036 2.05 to 2.07 (0.0808 to 0.0814)
90564-76025 1.83 to 1.85 (0.0721 to 0.0728) 90564-76037 2.07 to 2.09 (0.0815 to 0.0822)
90564-76026 1.85 to 1.87 (0.0729 to 0.0736) 90564-76038 2.09 to 2.11 (0.0823 to 0.0830)
90564-76027 1.87 to 1.89 (0.0737 to 0.0744) 90564-76039 2.11 to 2.13 (0.0831 to 0.0838)
90564-76028 1.89 to 1.91 (0.0745 to 0.0751) 90564-76040 2.13 to 2.15 (0.0839 to 0.0846)
90564-76029 1.91 to 1.93 (0.0752 to 0.0759) 90564-76041 2.15 to 2.17 (0.0847 to 0.0854)
90564-76030 1.93 to 1.95 (0.0760 to 0.0767) 90564-76042 2.17 to 2.19 (0.0855 to 0.0862)




Hide 41204B 13.REMOVE REAR DRIVE PINION NUT

Z101186

Click here(Click here)

Hide 41204 14.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Z101186

Click here(Click here)

Hide 41214 15.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 16.REMOVE DIFFERENTIAL BEARING CAP

Z101186

Click here(Click here)

Hide 17.REMOVE DIFFERENTIAL CASE ASSEMBLY

Z101186

Click here(Click here)

Hide 18.REMOVE DIFFERENTIAL DRIVE PINION

Z101186

Click here(Click here)

Hide 41231 19.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41201B 20.REMOVE REAR DRIVE PINION FRONT BEARING (INNER)

Z101186

Click here(Click here)

Hide 41201B 21.REMOVE REAR DRIVE PINION FRONT BEARING (OUTER)

Hide 41201A 22.REMOVE REAR DRIVE PINION REAR BEARING (INNER)

Z101186

Click here(Click here)

Hide 41201A 23.INSTALL REAR DRIVE PINION REAR BEARING (OUTER)

a.
C458098C01
2.938,0.458 3.438,0.458 true 2.885,1.125 3.385,1.125 true 3.781,1.229 4.281,1.229 true 2.708,1.479 2.885,1.479 2.885,1.479 3.375,1.271 true 2.396,1.396 2.708,1.552 0.313,0.156 10 false *2 2.573,1.042 2.979,1.292 0.406,0.25 10 false SST 2.625,0.365 3.031,0.615 0.406,0.25 10 false SST 0.458,0.115 0.74,0.469 0.281,0.354 18 false i 4.333,1.156 4.646,1.313 0.313,0.156 10 false *1
*1 Rear Drive Pinion Rear Tapered Roller Bearing (Outer) *2 Adjust Shim


i.

Using SST and a press, press the adjust shim and rear drive pinion rear tapered roller bearing (outer) into the differential carrier.

SST
09316-60012  (09316-00011)
09950-60011  (09951-00910)



Hide 41201B 24.INSTALL REAR DRIVE PINION FRONT BEARING (OUTER)

a.
C458112C01
3.51,0.438 3.188,0.438 3.188,0.438 3.542,0.75 true 3.781,0.844 4.313,0.844 true 2.885,0.365 3.302,0.604 0.417,0.24 10 false SST 4.406,0.771 4.823,1.01 0.417,0.24 10 false *1 0.448,0.146 0.771,0.479 0.323,0.333 18 false i
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer) - -


i.

Using SST and a press, press the rear drive pinion front tapered roller bearing (outer) into the differential carrier.

SST
09316-60012  (09316-00011, 09316-00031)



Hide 41231 25.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C458113


Hide 41201B 26.INSTALL REAR DRIVE PINION FRONT BEARING (INNER)

a.
C458114


Hide 27.INSTALL DIFFERENTIAL DRIVE PINION

a.
C458115N01
3.76,0.281 4.219,0.281 true 4.313,2.063 4.01,1.896 4.01,1.896 4.333,1.792 true 3.5,0.208 3.865,0.427 0.365,0.219 10 false SST 3.708,1.813 4.073,2.031 0.365,0.219 10 false SST 0.438,0.115 0.719,0.469 0.281,0.354 18 false i

i.

Using SST and a press, install the differential drive pinion.

SST
09316-60012  (09316-00011, 09316-00031)
09608-04031  



Hide 28.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C459337N01
0.469,0.115 0.75,0.469 0.281,0.354 18 false i

i.

Place the 2 rear differential case bearings (outer) to their respective bearings.

HINT:

Make sure the right and left races are not interchanged.




Hide 29.INSTALL DIFFERENTIAL BEARING CAP

a.
C458119C01
2.583,0.75 2.583,1.083 2.583,1.083 3.667,1.083 true 2.406,0.75 3.24,0.75 true 2.188,0.667 2.5,0.865 0.313,0.198 10 false *a 0.177,0.083 1.083,0.5 0.906,0.417 18 false i - iii
*a Matchmark - -


i.

Install the 2 plate washers.


ii.

Align the matchmarks on the differential bearing cap and differential carrier.


iii.

Install the right and left differential bearing caps with the 4 bolts.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)



Hide 41214 30.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 31.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Z101186

(Click here)

Hide 41204 32.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C458101C02
1.385,0.542 1.802,0.542 true 5.5,0.594 5.583,0.25 5.583,0.25 5.75,0.25 true 3.104,0.833 3.417,0.99 0.313,0.156 10 false *a 0.833,1.5 1.146,1.656 0.313,0.156 10 false *b 1.042,0.458 1.5,0.656 0.458,0.198 10 false SST 5.813,0.156 6.271,0.354 0.458,0.198 10 false SST 0.521,0.156 0.927,0.479 0.406,0.323 18 false i, ii 3.688,0.146 4.281,0.469 0.594,0.323 18 false iii, iv
*a Turn *b Hold


i.

Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



ii.

Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.


iii.

Using SST to hold the companion flange in place, install a new nut.

SST
09330-00021  (09330-00030)

Limit torque value:

457 N*m (4660 kgf*cm, 337 ft.*lbf) or less




Hide 33.INSPECT TOTAL PRELOAD

a.
C458107N02
0.125,0.083 0.708,0.406 0.583,0.323 18 false i, ii

i.

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.


ii.

Using a torque wrench, measure the total preload.

Standard Total Preload:
Reduction Ratio Bearing Preload
3.307 New bearing 1.24 to 2.83 N*m (13 to 28 kgf*cm, 11 to 25 in.*lbf)
Reused bearing 1.24 to 2.60 N*m (13 to 26 kgf*cm, 11 to 23 in.*lbf)


If necessary, disassemble and inspect the differential.



Hide 34.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C459347N01
0.51,0.135 0.792,0.49 0.281,0.354 18 false i

i.

Using a dial indicator, check the backlash of the differential ring gear.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 41204 35.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C458418C01
4.375,1.552 4.531,1.719 0.156,0.167 10 true *a 0.125,0.052 0.406,0.406 0.281,0.354 18 false i
*a 36 mm (1.42 in.) - -


i.

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)




Hide 36.STAKE DRIVE PINION NUT

a.
C458419