If you cannot proceed to the fingerprint registration screen, there may be a malfunction between the certification ECU (smart key ECU assembly) and engine switch and a malfunction in the engine switch, or a dirty sensor.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the engine switch, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC is output. | B |
A
B
Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fingerprint Authentication Data Fix | Engine switch data status | No/Yes | No: Data not confirmed Yes: Data confirmed |
- |
| Tester Display |
|---|
| Fingerprint Authentication Data Fix |
Data confirmation status (fingerprint authentication) is "Yes"
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check whether the engine switch sensor is dirty.
Sensor not dirty
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the customization setting for the fingerprint authentication function.
| Result | Proceed to |
|---|---|
| Setting is "ON" | A |
| Setting is not "ON" | B |
A
B
Check whether the registered user is touching the engine switch sensor.
| Result | Proceed to |
|---|---|
| Touched by the same user | A |
| Touched by a different user | B |
A
B
Disconnect and then reconnect the negative (-) battery terminal.
Check whether you can enter the fingerprint registration screen.
Registered normally
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check whether you can enter fingerprint registration mode using the GTS.
| Result | Proceed to |
|---|---|
| Can enter fingerprint registration mode | A |
| Cannot enter fingerprint registration mode | B |
A
B
Set the customization setting of the fingerprint authentication function to "ON".
| Proceed to |
|---|
| NEXT |
NEXT
Check whether you can enter the fingerprint registration screen.
| Result | Proceed to |
|---|---|
| Can enter fingerprint registration screen | A |
| Cannot enter fingerprint registration screen | B |
A
B
Wipe off dirt from the engine switch sensor.
When cleaning the surface of the sensor, use a soft, dry cloth without any fibers sticking out.
| Proceed to |
|---|
| NEXT |
NEXT
Check whether you can enter the fingerprint registration screen.
| Result | Proceed to |
|---|---|
| Can enter fingerprint registration screen | A |
| Cannot enter fingerprint registration screen | B |
A
B
Disconnect the I39 connector of the certification ECU (smart key ECU assembly).
Disconnect the I75 connector of the engine switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39,I75)Location & Routingewd_type=routing;type=c,c;code=I39,I75 |
||
| I39-8 (LIN) - I75-4 (LIN) | Always | Below 1 Ω |
| I39-8 (LIN) or I75-4 (LIN) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the I39 connector of the certification ECU (smart key ECU assembly).
Connect the I75 connector of the engine switch.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I75)Location & Routingewd_type=routing;type=c;code=I75 |
||
| I75-10 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I75)Location & Routingewd_type=routing;type=c;code=I75 |
||
| I75-3 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG