Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › TCM › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0467308 TCM A

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  TCM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C460420C02
5.719,1.365 7.125,3.75 1.406,2.385 3.24,0.052 5.156,0.938 1.917,0.885 6.302,0.167 6.885,0.167 false 0.417,2.417 0.667,1.333 0.667,1.333 0.833,1.333 false 1.833,3.333 1.917,3.583 1.917,3.583 2.083,3.583 false 4.25,0.333 4.25,0.573 false 4.906,1.563 5.677,0.917 5.677,0.917 5.844,0.917 false 6.25,2.208 6.25,2.042 false 2.833,2.333 3.417,2.333 false 6.281,0.594 6.865,0.594 false 5.719,2.667 7.125,2.667 false 6.073,3.469 6.073,3.302 false 0.615,2.917 1.073,3.115 0.458,0.198 10 false x 2 1.594,3.479 2.052,3.677 0.458,0.198 10 false x 2 2.146,3.479 2.604,3.74 0.458,0.26 10 false *1 0.885,1.219 1.344,1.417 0.458,0.198 10 false *2 1.833,2.469 2.292,2.667 0.458,0.198 10 false x 5 4.708,2.198 5.292,2.448 0.583,0.25 10 false x 4 (*D) 6.094,0 6.375,0.354 0.281,0.354 18 false 1 3.458,2.208 3.74,2.563 0.281,0.354 18 false 3 6.198,2.219 6.479,2.573 0.281,0.354 18 false 6 5.875,0.781 6.156,1.135 0.281,0.354 18 false 4 6.104,0.427 6.385,0.781 0.281,0.354 18 false 2 4.188,0.594 4.469,0.948 0.281,0.354 18 false 5 3.281,0.083 3.594,0.281 0.313,0.198 10 false *A 4.698,2 5.281,2.25 0.583,0.25 10 false x 6 (*C) 6.604,3.521 6.938,3.719 0.333,0.198 10 false x 2 6.042,3.479 6.417,3.75 0.375,0.271 18 false 6 5.781,1.406 6.333,1.677 0.552,0.271 10 false *A, C 5.771,2.698 6.323,2.969 0.552,0.271 10 false *B, C

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - - - -
3 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
4 NO. 2 ENGINE UNDER COVER ASSEMBLY 51420 - - -
5 FRAME UNDER COVER ASSEMBLY RH 51430A - - -
6 FRAME UNDER COVER ASSEMBLY LH 51450C - - -

*A for V35A-FTS *B for F33A-FTV
*C w/ Cover *D w/o Cover
*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH

C456950N01
3,0.563 3.302,0.354 3.302,0.354 3.469,0.354 false 4.167,1.333 4.167,0.25 4.167,0.25 4.417,0.25 false 3.563,0.24 3.875,0.438 0.313,0.198 10 false *1 4.667,0.594 4.979,0.792 0.313,0.198 10 false x 4 4.75,0.125 5.031,0.479 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

7 TCM 89530C (Click here) - -

*1 TRANSFER BREATHER HOSE SUB-ASSEMBLY - -

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the TCM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)
TCM
If possible to read the transmission compensation code from the previous TCM
·

Perform AT unit compensation (read compensation code) and AT unit compensation (register compensation code (automatic input))

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Engine overruns


Registration:
(Click here)
Initialization:
(Click here)
If impossible to read the transmission compensation code from the previous TCM
·

Perform AT unit compensation (fixed value writing)

·

Perform road test to allow TCM to learn


ECU configuration - (Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

(Click here)


HINT:

When the TCM (when the vehicle ECU compensation code can be read) is replaced, perform AT unit compensation (read compensation code) before replacement.

(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51410 3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51420 4.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51430A 5.REMOVE FRAME UNDER COVER ASSEMBLY RH

Hide 51450C 6.REMOVE FRAME UNDER COVER ASSEMBLY LH (w/ Cover)

Hide 89530C 7.REMOVE TCM

a.
C456932C01
0.135,0.083 0.354,0.385 0.219,0.302 18 false i 3.969,0.135 4.25,0.49 0.281,0.354 18 false ii 1.969,1.99 2.25,2.344 0.281,0.354 18 false iii
V113147

While Pressing the Lever Lock
V113148

Pull Up the Lever


i.

Detach the clamp and disconnect the transfer breather hose sub-assembly.


ii.

While pressing the lever lock, disconnect the TCM connector as shown in the illustration.


iii.

Remove the 4 bolts and TCM from the automatic transmission assembly.