| *A | w/ Tonneau Cover | *B | w/ Rear No. 2 Seat |
| *C | w/ Curtain Shield Airbag | *D | w/ Air Duct |
| *1 | TERMINAL COVER | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | REAR FLOOR MAT REAR SUPPORT PLATE | 58574G | - | - | - |
| 12 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 13 | REAR FLOOR BOARD REAR LH | 58418H | - | - | - |
| 14 | REAR FLOOR BOARD REAR RH | 58417B | - | - | - |
| 15 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 16 | REAR DECK TRIM COVER | 64716P | - | - | - |
| 17 | ROPE HOOK ASSEMBLY | 66310N | - | - | - |
| 18 | REAR FLOOR CARPET ASSEMBLY | 58570C | - | - | - |
| 19 | TONNEAU COVER ASSEMBLY | 64910M | - | - | - |
| 20 | REAR NO. 2 SEAT ASSEMBLY RH | - | - | - | - |
| *A | w/ Tonneau Cover | *B | w/ Rear No. 2 Seat |
| *C | w/o Rear No. 2 Seat | *D | w/ Carpet |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
86011V 1.INSTALL RADIO SETTING CONDENSER
|
Install in this Direction | - | - |
Attach the claw to install a new terminal cover to the wire harness.
Make sure to hold the crimping side of the terminal when installing the wire harness to the terminal cover.
Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.
Do not use excessive force when inserting the wire harness into the terminal cover.
If the terminal cover has been deformed during installation, replace the terminal and terminal cover with new ones.
Attach the claw to install 2 new terminal covers with wire harness to a new condenser.
Do not use excessive force when inserting the terminal covers into the condenser.
If a terminal cover has been deformed during installation, replace the terminal, terminal covers and condenser with new ones.
Insert the cover as shown in the illustration and attach the claw.
Attach the clamp to temporarily install a new radio setting condenser with wire harness.
Install the radio setting condenser with the bolt.
87217N 2.INSTALL REAR NO. 9 SIDE AIR DUCT (w/ Air Duct)
3.INSTALL COOLER PLATE (w/ Air Duct)
62471A 4.INSTALL INNER ROOF SIDE GARNISH RH
62510M 5.INSTALL QUARTER TRIM PANEL ASSEMBLY RH
64937A 6.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
73560 7.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73360C 8.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
73233D 9.INSTALL OUTER LAP BELT ANCHOR COVER
67917C 10.INSTALL REAR DOOR SCUFF PLATE RH
58574G 11.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 12.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58418H 13.INSTALL REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 14.INSTALL REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58410B 15.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 16.INSTALL REAR DECK TRIM COVER (w/o Rear No. 2 Seat)
66310N 17.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
58570C 18.INSTALL REAR FLOOR CARPET ASSEMBLY (w/ Carpet)
64910M 19.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
20.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>INSTALLATION