| *A | w/ Tonneau Cover | *B | w/ Rear No. 2 Seat |
| *C | w/ Curtain shield Airbag | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/o Rear No. 2 Seat |
| *C | w/ Tonneau Cover | *D | w/ Carpet |
|
N*m (kgf*cm, ft.*lbf) : Specified torque | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
73370C 1.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
| *A | w/ Pretensioner | - | - |
| *a | Unlock | *b | Lock |
| *c | 45° | - | - |
|
Bolt A |
|
Pretensioner Connector |
|
Bolt B |
|
Bolt C |
When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
Do not disassemble the retractor.
Attach the guide.
Install the rear No. 1 seat outer belt assembly LH with the bolt B and bolt C.
w/ Pretensioner:
1. Connect the pretensioner connector.
Refer to How to Connect or Disconnect Airbag Connector:
Tighten the bolt A and install the shoulder anchor of the rear No. 1 seat outer belt assembly LH.
62582E 2.INSTALL QUARTER PILLAR GARNISH LH
62520B 3.INSTALL QUARTER TRIM PANEL ASSEMBLY LH
64937A 4.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
73570 5.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73370C 6.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73233D 7.INSTALL OUTER LAP BELT ANCHOR COVER
67918D 8.INSTALL REAR DOOR SCUFF PLATE LH
58574G 9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 10.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58418H 11.INSTALL REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 12.INSTALL REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58410B 13.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 14.INSTALL REAR DECK TRIM COVER (w/o Rear No. 2 Seat)
66310N 15.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
58570C 16.INSTALL REAR FLOOR CARPET ASSEMBLY (w/ Carpet)
64910M 17.INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)
18.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>INSTALLATION
19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 1GR-FE:
for V35A-FTS:
for F33A-FTV:
20. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART