Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › from 2021.07
RM38G0E _58 Vehicle Interior _100751 SUPPLEMENTAL RESTRAINT SYSTEMS _0467878 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B612029N01
6.521,0.229 6.771,0.229 true 6.49,0.646 6.74,0.646 true 4.552,3.229 4.823,3.229 true 5.927,1.833 5.927,2.083 true 2.083,1.656 2.083,1.906 true 4.146,1.74 3.896,1.74 true 2.906,2.146 2.906,2.396 true 1.052,3.073 1.052,3.323 true 6.396,0.063 6.677,0.417 0.281,0.354 18 false 1 6.344,0.469 6.625,0.823 0.281,0.354 18 false 2 0.99,2.802 1.271,3.156 0.281,0.354 18 false 3 2.01,1.875 2.292,2.229 0.281,0.354 18 false 5 5.854,1.573 6.135,1.927 0.281,0.354 18 false 4 4.177,1.583 4.458,1.938 0.281,0.354 18 false 7 2.833,2.354 3.115,2.708 0.281,0.354 18 false 6 5.115,3.063 5.396,3.417 0.281,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL - (Click here) - -
3 FRONT DOOR SCUFF PLATE LH 67914B - - -
4 REAR DOOR SCUFF PLATE LH 67918D - - -
5 OUTER LAP BELT ANCHOR COVER 73233 - - -
6 FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) 73220 - - -
7 CENTER PILLAR LOWER GARNISH LH 62414A - - -
8 FLOOR SIDE AIRBAG SENSOR LH 89831E (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the floor side airbag sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





Hide 67914B 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67918D 4.REMOVE REAR DOOR SCUFF PLATE LH

Hide 73233 5.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 6.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)

Hide 62414A 7.REMOVE CENTER PILLAR LOWER GARNISH LH

Hide 89831E 8.REMOVE FLOOR SIDE AIRBAG SENSOR LH

a.
B608600C01
0.583,0.667 1.167,0.667 true 4.208,0.094 4.531,0.417 0.323,0.323 18 false ii 0.438,0.563 0.708,0.771 0.271,0.208 10 false *a 0.625,0.094 0.948,0.417 0.323,0.323 18 false i
*a Turns off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B608787N01
0.563,0.073 0.844,0.427 0.281,0.354 18 false i 5.542,0.073 5.823,0.427 0.281,0.354 18 false ii 5.24,0.792 5.521,1.146 0.281,0.354 18 false iii

i.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



ii.

Remove the bolt.

NOTICE:
·

Loosen the bolt while holding the floor side airbag sensor LH because the floor side airbag sensor LH claw is easily damaged.

·

If the floor side airbag sensor LH has been dropped, replace it with a new one.




iii.

Disengage the claw to remove the floor side airbag sensor LH.