| *A | w/ Climate Control Seat System | *B | w/ Wire Harness |
| *1 | NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY RH | *2 | SPRING NUT |
| *3 | PLATE WASHER | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft*lbf) : Specified torque |
|
Toyota Genuine Adhesive 1324, Three Bond 2468 or equivalent. | ★ | Precpated part |
| ● | Non-reusable part | - | - |
| *A | w/ Rear Seat Side Airbag | *B | w/ Seat Heater System |
| *C | w/ Child Restraint System Guide | - | - |
| *1 | REAR NO. 1 SEAT CUSHION PAD RH | *2 | NO. 1 SEATBACK PAD RH |
| *3 | HOG RING | *4 | RIVET |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
| *A | w/o Wire Harness | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 54 | NO. 1 SEATBACK LOCK ASSEMBLY | 72630H | - | - | - |
| 55 | NO. 1 SEAT NO. 2 ARMREST ASSEMBLY | 72810M | - | - | - |
| 56 | CENTER NO. 1 SEATBACK FRAME SUB-ASSEMBLY | 79103C | - | - | - |
| 57 | REAR SEAT HEADREST SUPPORT ASSEMBLY | 71930Q | - | - | - |
| 58 | FOLD SEATBACK WIRE | 79873A | - | - | - |
| 59 | RECLINING CONTROL LEVER RH | 72574B | - | - | - |
| 60 | CUP HOLDER ASSEMBLY | 66990V | - | - | - |
| 61 | REAR CENTER SEAT ARMREST ASSEMBLY | 72830X | - | - | - |
| 62 | NO. 1 SEAT NO. 1 ARMREST ASSEMBLY | 72810L | - | - | - |
| 63 | CENTER ARMREST HINGE COVER RH | 72868C | - | - | - |
| 64 | CENTER ARMREST HINGE COVER LH | 72869A | - | - | - |
| 65 | REAR CENTER NO. 1 SEATBACK BOARD | 71881E | - | - | - |
| 66 | REAR NO. 2 SEATBACK COVER | 72996J | - | - | - |
| 67 | REAR SEAT HINGE COVER LH | 71486F | - | - | - |
| 68 | SEATBACK STOPPER PLATE | 72569B | - | - | - |
| 69 | CENTER SEATBACK ASSEMBLY | - | - | - | - |
| 70 | REAR NO. 1 SEAT RECLINING COVER LH | 71834S | - | - | - |
| *A | w/ Child Restraint System Guide | - | - |
| *1 | REAR SEAT CENTER ARMREST COVER | *2 | NO. 1 SEATBACK BOARD COVER |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
| ● | Non-reusable part | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
1.INSTALL REAR SEAT CUSHION PAD B (w/ Climate Control Seat System)
85860E 2.INSTALL NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH (w/ Climate Control Seat System)
Temporarily install the No. 1 seat cushion climate control blower assembly to the No. 1 seat cushion frame sub-assembly RH.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivets perpendicularly to the installation holes. Using the air riveter, install the No. 1 seat cushion climate control blower assembly with the rivets.
When installing the rivets to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Pull the trigger again to cut off the rivet if it is not cut off.
Attach the claw.
82193 3.INSTALL REAR SEAT WIRE RH
78910C 4.INSTALL SEAT FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
72570E 5.INSTALL NO. 1 SEAT RECLINING ADJUSTING CABLE ASSEMBLY RH
72650J 6.INSTALL REAR SEAT LOCK ASSEMBLY RH
72660P 7.INSTALL REAR SEAT LOCK ASSEMBLY LH
72143D 8.INSTALL REAR SEAT LOWER TRACK BRACKET RH
71461H 9.INSTALL REAR SEAT CUSHION SPRING
85867D 10.INSTALL NO. 1 SEAT SEATBACK CLIMATE CONTROL BLOWER RH (w/ Climate Control Seat System)
Temporarily install the No. 1 seat seatback climate control blower RH to the No. 1 seatback frame sub-assembly RH.
Install the No. 4 nose piece to an air riveter and insert the mandrel section of a new φ 4 mm rivet into the nose piece.
Press the rivets perpendicularly to the installation holes. Using the air riveter, install the No. 1 seat seatback climate control blower RH with the rivets.
When installing the rivets to the panel surface, do not tilt the riveter.
Do not leave a gap between the rivet head portion and the panel.
Pull the trigger again to cut off the rivet if it is not cut off.
Attach the claw.
72307D 11.INSTALL NO. 1 RECLINING CONTROL LINK SUB-ASSEMBLY RH
79103B 12.INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH
| *a | Cable End | - | - |
|
Install in this Direction |
|
Bolt |
|
"TORX" Bolt | - | - |
Clean the bolt holes in the No. 1 seat cushion frame sub-assembly RH.
Apply adhesive to the threads of the 2 "TORX" bolts in the area shown in the illustration.
Toyota Genuine Adhesive 1324, Three Bond 2468 or equivalent.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 2.5 to 5.5mm | B | 10.5 to 13.5mm |
Temporarily install the No. 1 seatback frame sub-assembly RH with the 3 bolts and 2 "TORX" bolts.
While pushing in the direction shown in the illustration, using a T55H wrench torx for tamper resistant, install the No. 1 seatback frame sub-assembly RH with the 2 "TORX" bolts in the order shown in the illustration.
While pushing in the direction shown in the illustration, tighten the 3 bolts.
Turn each cable end in the installation direction shown in the illustration and connect each cable end.
Attach each casing cap.
72551M 13.INSTALL SEAT RECLINING HINGE COVER RH
72552K 14.INSTALL SEAT RECLINING HINGE COVER RH
71879H 15.INSTALL REAR INNER SEAT RECLINING COVER LH
71H75L 16.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH
71H76L 17.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH
71485E 18.INSTALL REAR SEAT HINGE COVER
71694G 19.INSTALL REAR INNER SEAT CUSHION HINGE COVER LH
79117D 20.INSTALL NO. 1 SEAT CUSHION CARPET (w/ Child Restraint System Guide)
| *1 | NO. 1 SEATBACK FRAME SUB-ASSEMBLY RH | - | - |
| *a | Fastener | - | - |
|
Install in this Direction | - | - |
Follow the procedure below to install the No. 1 seat cushion carpet.
1. Pass the slit part of the No. 1 seat cushion carpet through the wire part of No. 1 seatback frame sub-assembly RH.
2. Wrap the No. 1 seat cushion carpet around the pipe of the No. 1 seatback frame sub-assembly RH and attach it with a fastener as shown in the illustration.
71293B 22.INSTALL REAR UPPER SEATBACK PLATE
79013D 24.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY RH
25.INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH
71930Q 26.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
73373 27.INSTALL REAR SEAT SHOULDER BELT COVER
73178A 28.INSTALL SEAT BELT ANCHOR COVER CAP
71075F 33.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY RH
34.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH
71701A 35.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH
72996H 36.INSTALL REAR SEATBACK COVER (w/ Child Restraint System Guide)
87501E 37.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
73310D 38.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY (SEAT ANCHOR)
73350 40.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
72927F 41.INSTALL REAR SEAT CUSHION UNDER COVER RH
|
Screw A |
|
Screw B |
|
Screw C | - | - |
Install the rear seat cushion under cover RH with the screw A.
Install the screw B.
Install the 7 screws C.
Attach the J hook of the No. 1 seat cushion cover sub-assembly RH.
72995F 42.INSTALL REAR SEAT CUSHION COVER RH
71301G 43.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
71302C 44.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
82193 45.INSTALL REAR SEAT WIRE RH (w/o Wire Harness)
79967W 46.INSTALL REAR NO. 1 SEAT NO. 4 LEG SIDE COVER
79951B 47.INSTALL NO. 1 SEAT NO. 1 CUSHION COVER
79952A 48.INSTALL NO. 1 SEAT NO. 2 CUSHION COVER
76971G 49.INSTALL REAR UNDER COVER
78950F 50.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
71833S 51.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
72525R 52.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
|
Pushed Place |
|
Push in this Direction |
While pressing the reclining adjuster release handle RH as shown in the illustration, install the reclining adjuster release handle RH with the screw.
72329F 53.INSTALL REAR SEAT ADJUSTER BOLT COVER
72630H 54.INSTALL NO. 1 SEATBACK LOCK ASSEMBLY
72810M 55.INSTALL NO. 1 SEAT NO. 2 ARMREST ASSEMBLY
79103C 56.INSTALL CENTER NO. 1 SEATBACK FRAME SUB-ASSEMBLY
71930Q 57.INSTALL REAR SEAT HEADREST SUPPORT ASSEMBLY
79873A 58.INSTALL FOLD SEATBACK WIRE
72574B 59.INSTALL RECLINING CONTROL LEVER RH
66990V 60.INSTALL CUP HOLDER ASSEMBLY
72830X 61.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY
72810L 62.INSTALL NO. 1 SEAT NO. 1 ARMREST ASSEMBLY
72868C 63.INSTALL CENTER ARMREST HINGE COVER RH
72869A 64.INSTALL CENTER ARMREST HINGE COVER LH
71881E 65.INSTALL REAR CENTER NO. 1 SEATBACK BOARD
72996J 66.INSTALL REAR NO. 2 SEATBACK COVER (w/ Child Restraint System Guide)
71486F 67.INSTALL REAR SEAT HINGE COVER LH
72569B 68.INSTALL SEATBACK STOPPER PLATE
69.INSTALL CENTER SEATBACK ASSEMBLY
71834S 70.INSTALL REAR NO. 1 SEAT RECLINING COVER LH