Refer to DTC P023A12.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P023A12
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P023A14 | Charge Air Cooler Coolant Pump Control Circuit Short to Ground or Open | When the output duty of the electric water pump assembly is 30 to 85%, the IWPO output is continuously equal to or less than the judgment value for 3 seconds or more. (1 trip detection logic) |
·
Open or short in electric water pump assembly circuit
·
Electric water pump assembly
·
ECM |
Comes on | SAE Code: P023B |
| DTC No. | Data List |
|---|---|
| P023A14 |
·
Intercooler Water Pump Speed
·
Intercooler Water Pump |
The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.
The electric water pump assembly is controlled steplessly by the drive duty signal (IWPO) output from the ECM.
The ECM monitors the actual drive duty cycle signal (IWPO) while simultaneously outputting the drive duty signal (IWPO) to the electric water pump assembly.
If the actual drive duty signal (IWPO) is less than or equal to the threshold value while the drive duty signal (IWPO) is being output to the electric water pump assembly, the ECM detects a malfunction and stores a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P023A14 | After fully warming up, increase and maintain the engine speed so that the intercooler water pump duty ratio is 30% or more for 3 seconds or longer. |
Refer to DTC P023A12.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P023A12
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the electric water pump assembly connector.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.
Measure the resistance according to the value(s) in the table below.
| Tester Display |
|---|
| Control the Intercooler Water Pump |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B29)Location & Routingewd_type=routing;type=c;code=B29 |
||
| B29-3 (SWP) - Body ground | Before Active Test → Active Test in progress | Before Active Test: Resistance stabilized → Active Test in progress: Resistance changes* |
*: The transistor inside the ECM is controlled by performing the Active Test.
The resistance of the SWP terminal changes while the Active Test is in progress due to duty control.
If the resistance fluctuates while the Active Test is being performed from the resistance that stabilized before the Active Test was performed, it can be judged that the transistor is operating.
If the transistor does not operate while the Active Test is being performed, the ECM may be malfunctioning.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric water pump assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B29,B70)Location & Routingewd_type=routing;type=c,c;code=B29,B70 |
||
| B29-3 (SWP) - B70-37 (IWPO) | Always | Below 1 Ω |
| B29-3 (SWP) or B70-37 (IWPO) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG