A No. 1 nitrogen oxides sensor is installed in the exhaust manifold converter sub-assembly in order to detect the concentration of NOx and O2 in the exhaust gas.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P013013 | O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Open | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P0130 |
| P220011 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Short to Ground | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P2202 |
| P220012 | NOx Sensor Circuit High Bank 1 Sensor 1 Circuit Short to Battery | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P2203 |
| P220013 | NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Open | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P2200 |
| P220512 | NOx Sensor Heater Control Circuit High Bank 1 Sensor 1 Circuit Short to Battery | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P2207 |
| P220514 | NOx Sensor Heater Control Circuit Low Bank 1 Sensor 1 Circuit Short to Ground or Open | No. 1 nitrogen oxides sensor malfunction for 3 seconds or more. (2 trip detection logic) |
No. 1 nitrogen oxides sensor | Comes on | SAE Code: P2206 |
| DTC No. | Data List |
|---|---|
| P013013 P220011 P220012 P220013 P220512 P220514 |
NOx Density B1S1 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P013013 P220011 P220012 P220013 P220512 P220514 |
Ignition switch ON for 3 seconds or more |
Refer to DTC U010E87.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>U010E87
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P013013, P220011, P220012, P220013, P220512 or P220514 is output | A |
| DTC P013013, P220011, P220012, P220013, P220512 or P220514 and other DTCs are output* | B |
*: If any other DTCs are output, perform troubleshooting for those DTCs first.
A
B
Replace the No. 1 nitrogen oxides sensor.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
Perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 3 seconds or more.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P013013, P220011, P220012, P220013, P220512 or P220514.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, turn the ignition switch to ON and wait for 3 seconds or more, and then check "All Readiness" again.
| Proceed to |
|---|
| NEXT |
NEXT