These DTCs indicate that the variable vane DC motor of the turbocharger is malfunctioning. The ECM monitors the variable vane DC motor current to detect an open or short in the variable vane DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.
The variable vane DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the variable vane DC motor in accordance with the driving conditions.
If the nozzle vane is stuck closed (Variable vane DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (Variable vane DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P004518 | Turbocharger/Supercharger Boost Control "A" Circuit Current Below Threshold | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more. (1 trip detection logic) |
·
Open in variable vane DC motor (turbocharger nozzle vane control actuator bank 1) circuit
·
Turbocharger nozzle vane control actuator bank 1
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P0047 |
| P004519 | Turbocharger/Supercharger Boost Control "A" Circuit Current Above Threshold | Overcurrent is detected 25 times or more. (1 trip detection logic) |
·
Short in variable vane DC motor (turbocharger nozzle vane control actuator bank 1) circuit
·
Turbocharger nozzle vane control actuator bank 1
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P0048 |
| P004600 | Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance | The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more. (1 trip detection logic) |
·
Turbocharger nozzle vane control actuator bank 1
·
No. 1 Turbocharger sub-assembly
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P0046 |
| P12A000 | Turbocharger/Supercharger Boost Control "C" Circuit Range/Performance | The difference between the target NV opening angle and the actual VN opening angle is 50% or greater for 65 seconds or more. (1 trip detection logic) |
·
Turbocharger nozzle vane control actuator bank 2
·
No. 2 Turbocharger sub-assembly
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P12A1 |
| P12A018 | Turbocharger/Supercharger Boost Control "C" Circuit Current Below Threshold | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more. (1 trip detection logic) |
·
Open in variable vane DC motor (turbocharger nozzle vane control actuator bank 2) circuit
·
Turbocharger nozzle vane control actuator bank 2
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P12A2 |
| P12A019 | Turbocharger/Supercharger Boost Control "C" Circuit Current Above Threshold | Overcurrent is detected 25 times or more. (1 trip detection logic) |
·
Short in variable vane DC motor (turbocharger nozzle vane control actuator bank 2) circuit
·
Turbocharger nozzle vane control actuator bank 2
·
Turbocharger nozzle vane is stuck or movement is irregular |
Comes on | SAE Code: P12A3 |
If DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 is stored due to the nozzle vane being stuck closed, the following symptom may appear:
Vehicle surge when driving with full load
If DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P004518 P004519 P004600 |
Maintain the Active Test "Activate the VN Turbo Open Bank 1" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more. |
| P12A000 P12A018 P12A019 |
Maintain the Active Test "Activate the VN Turbo 1 and 2 Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
When replacing the turbocharger nozzle vane control actuator, initialize the learning values after replacement.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
When replacing the turbocharger sub-assembly, calibrate the VN turbo offset voltage value and initialize the learning values after replacement.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P004600 and/or P12A000 is output | A |
| DTC P004518, P004519, P12A018 and/or P12A019 is output | B |
| DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 and other DTCs are output | C |
If codes other than DTC P004518, P004519, P004600, P12A000, P12A018 and/or P12A019 are output, perform troubleshooting for those DTCs first.
A
B
C
Loosen the installation bolt of the turbocharger nozzle vane control actuator.
| *1 | No. 1 Turbocharger Sub-assembly | *2 | No. 2 Turbocharger Sub-assembly |
| *3 | Installation Bolt | *4 | E-washer |
Remove the e-washer from the turbocharger nozzle vane control actuator.
Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane plate moves.
| Result | Proceed to |
|---|---|
| Catches, but operates* | OK |
| Gets stuck and does not operate | NG |
*: Check several times.
OK
NG
Replace the turbocharger nozzle vane control actuator.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Replace the malfunctioning turbocharger sub-assembly.
Replace the No. 1 turbocharger sub-assembly.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL
Replace the No. 2 turbocharger sub-assembly.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component without harness connected (Variable Vane DC Motor) |
Disconnect the variable vane DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 1 to 100 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the variable vane DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C159,C138,C163)Location & Routingewd_type=routing;type=c,c,c;code=C159,C138,C163 |
||
| C159-1 (M-) - C138-25 (VNM-) | Always | Below 1 Ω |
| C159-2 (M+) - C138-6 (VNM+) | Always | Below 1 Ω |
| C163-1 (M-) - C138-26 (VN2-) | Always | Below 1 Ω |
| C163-2 (M+) - C138-7 (VN2+) | Always | Below 1 Ω |
| C159-1 (M-) or C138-25 (VNM-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C159-2 (M+) or C138-6 (VNM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C163-1 (M-) or C138-26 (VN2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C163-2 (M+) or C138-7 (VN2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo 1 and 2 Open.
| Tester Display |
|---|
| Activate the VN Turbo 1 and 2 Open |
Maintain the Active Test "Activate the VN Turbo 1 and 2 Open" at Open (VN turbo fully open) and OFF (normal control) for 65 seconds or more.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the turbocharger nozzle vane control actuator.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT