The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P007A11 | Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Ground | Short in the intake air temperature sensor (for intercooler outlet) circuit for 0.5 seconds or more. (1 trip detection logic) |
·
Short in intake air temperature sensor (for intercooler outlet) circuit
·
intake air temperature sensor (for intercooler outlet)
·
ECM |
Comes on | SAE Code: P007C |
| P007A15 | Charge Air Cooler Temperature Sensor Bank 1 Circuit Short to Battery or Open | Conditions (a) and (b) continue for 0.5 seconds or more: (a) Intake air temperature is -30°C (-22°F) or higher. (b) Open in the intake air temperature sensor (for intercooler outlet) circuit. (1 trip detection logic) |
·
Open in intake air temperature sensor (for intercooler outlet) circuit
·
intake air temperature sensor (for intercooler outlet)
·
ECM |
Comes on | SAE Code: P007D |
| DTC No. | Data List |
|---|---|
| P007A11 P007A15 |
Intake Air Temperature B1S1 (Turbo) |
If DTC P007A11 or P007A15 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P007A11 P007A15 |
Ignition switch ON for 1 second or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
Same as air temperature near intake manifold.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 190°C (374°F) or higher | B |
| OK (same as air temperature near intake manifold) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 190°C (374°F) or higher.
A
B
C
| *1 | Intake Air Temperature Sensor (For Intercooler Outlet) |
| *2 | ECM |
| *a | Front view of wire harness connector (to Intake Air Temperature Sensor (For Intercooler Outlet)) |
Disconnect the intake air temperature sensor (for intercooler outlet) connector.
Connect terminals 1 (THA) and 2 (E2) of the intake air temperature sensor (for intercooler outlet) wire harness side connector.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
190°C (374°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (for intercooler outlet).
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (for intercooler outlet) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C171,C138)Location & Routingewd_type=routing;type=c,c;code=C171,C138 |
||
| C171-1 (THA) - C138-76 (THIA) | Always | Below 1 Ω |
| C171-2 (E2) - C138-77 (ETHI) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Intake Air Temperature Sensor (For Intercooler Outlet) |
| *2 | ECM |
Disconnect the intake air temperature sensor (for intercooler outlet) connector.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 (Turbo).
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S1 (Turbo) |
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (for intercooler outlet).
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (for intercooler outlet) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C171,C138)Location & Routingewd_type=routing;type=c,c;code=C171,C138 |
||
| C171-1 (THA) or C138-76 (THIA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT