Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P10C512  2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Battery  P10C514  2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Ground or Open  


DESCRIPTION

The manifold absolute pressure sensor (2nd turbocharger outlet side) monitors pressure on the compressor outlet side of the No. 2 turbocharger sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P10C512 2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Battery Manifold absolute pressure sensor (2nd turbocharger outlet side) voltage is 4.8 V or higher for more than 0.5 seconds.
(1 trip detection logic)
·

Open or short in manifold absolute pressure sensor (2nd turbocharger outlet side) circuit

·

Manifold absolute pressure sensor (2nd turbocharger outlet side)

·

ECM


Comes on SAE Code: P10C8
P10C514 2nd Turbocharger/Supercharger Outlet Pressure Sensor Circuit Short to Ground or Open Manifold absolute pressure sensor (2nd turbocharger outlet side) voltage is 0.1 V or less for more than 0.5 seconds.
(1 trip detection logic)
·

Open or short in manifold absolute pressure sensor (2nd turbocharger outlet side) circuit

·

Manifold absolute pressure sensor (2nd turbocharger outlet side)

·

ECM


Comes on SAE Code: P10C7

Related Data List
DTC No. Data List
P10C512
P10C514
·

2nd Turbocharger/Supercharger Outlet Pressure

·

Atmospheric Pressure



HINT:
·

If DTC P10C512 and/or P10C514 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P10C512 or P10C514 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine / Data List / 2nd Turbocharger/Supercharger Outlet Pressure.

Reference
GTS Displayed Malfunction
23 kPa (173 mmHg, 6.79 in.Hg)
·

Open in VC circuit

·

Open in PBC circuit

·

Short in PBC circuit


418 kPa (3135 mmHg, 123.44 in.Hg)
·

Open in E circuit





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P10C512
P10C514
2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A478140E05
1.115,1.719 1.646,1.927 0.531,0.208 10 false PBC 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.281,2.49 1.813,2.698 0.531,0.208 10 false E 4.771,0.917 5.302,1.125 0.531,0.208 10 false VPBC 4.479,0.917 5.01,1.125 0.531,0.208 10 false 93 4.469,2.385 5,2.594 0.531,0.208 10 false 92 4.479,1.615 5.01,1.823 0.531,0.208 10 false 70 4.771,2.385 5.302,2.594 0.531,0.208 10 false EPBC 4.781,1.604 5.313,1.813 0.531,0.208 10 false PBC 5.469,3.302 6.115,3.542 0.646,0.24 10 false ECM 5.458,3.135 5.99,3.344 0.531,0.208 10 false C138 0.073,2.896 0.604,3.104 0.531,0.208 10 false C113 0.073,3.073 4.448,3.781 4.375,0.708 10 false Manifold Absolute Pressure Sensor (2nd Turbocharger Outlet Side) 1.51,0.906 2.042,1.115 0.531,0.208 10 false 3 1.521,1.604 2.052,1.813 0.531,0.208 10 false 2 1.521,2.375 2.052,2.583 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (2ND TURBOCHARGER/SUPERCHARGER OUTLET PRESSURE)
a.

Enter the following menus: Powertrain / Engine / Data List / 2nd Turbocharger/Supercharger Outlet Pressure.

Powertrain > Engine > Data List
Tester Display
2nd Turbocharger/Supercharger Outlet Pressure
50003 372 1395

b.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmospheric Pressure" in the Data List.




Result:
Proceed to
OK
NG



OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE) - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE) - ECM)
a.

Disconnect the manifold absolute pressure sensor (2nd turbocharger outlet side) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C113,C138)Location & Routing

Click Connector(C113)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Diesel Turbo Pressure Sensor (for Compressor outlet)

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C113-3 (VC) - C138-93 (VPBC) Always Below 1 Ω
C113-2 (PBC) - C138-70 (PBC) Always Below 1 Ω
C113-1 (E) - C138-92 (EPBC) Always Below 1 Ω
C113-3 (VC) or C138-93 (VPBC) - Body ground and other terminals Always 10 kΩ or higher
C113-2 (PBC) or C138-70 (PBC) - Body ground and other terminals Always 10 kΩ or higher
C113-1 (E) or C138-92 (EPBC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VC TERMINAL)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (VC TERMINAL)
a.

Disconnect the manifold absolute pressure sensor (2nd turbocharger outlet side) connector.


b.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPLACE ECM
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the manifold absolute pressure sensor (2nd turbocharger outlet side) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C113)Location & Routing

Click Connector(C113)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Diesel Turbo Pressure Sensor (for Compressor outlet)

C113-3 (VC) - C113-2 (PBC) Ignition switch off No short or no open circuit
C113-2 (PBC) - C113-1 (E) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)

NG

6.REPLACE ECM
5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)
a.

Replace the manifold absolute pressure sensor (2nd turbocharger outlet side).

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 3 seconds.


d.

After the engine is started for 2 seconds, race the engine for 1 second.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P10C512 or P10C514.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, race the engine for 1 minute, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED