Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P011011  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground  P011015  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter sub-assembly and detects the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A283580E05
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P011011 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground Short in the intake air temperature sensor for 0.5 seconds.
(1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on SAE Code: P0112
P011015 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open Open in the intake air temperature sensor for 0.5 seconds.
(1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


Comes on SAE Code: P0113

Related Data List
DTC No. Data List
P011011
P011015
Intake Air Temperature B1S1

HINT:
·

If DTC P011011 and/or P011015 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P011011 or P011015 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1.

Reference
GTS Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P011011
P011015
Ignition switch ON for 1 second or more

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1)
a.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1
50003 372 613

b.

Read the value.

OK:

Same as actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter sub-assembly connector.

A335968C49
4.51,1.573 4.927,1.833 0.417,0.26 5.271,2.438 5.542,1.906 true 6.26,2.438 5.969,1.906 true 0.823,0.396 1.135,0.552 0.313,0.156 10 false *1 3.531,0.396 3.844,0.552 0.313,0.156 10 false *2 5.146,0.396 5.458,0.552 0.313,0.156 10 false *a 5.125,2.479 5.583,2.677 0.458,0.198 10 false E2G 6.188,2.5 6.646,2.698 0.458,0.198 10 false THA 4.625,1.635 5.083,1.833 0.458,0.198 10 false C25 1.76,1 2.219,1.198 0.458,0.198 10 false THA 3.594,1.021 4.052,1.219 0.458,0.198 10 false THA 3.625,1.531 4.083,1.729 0.458,0.198 10 false EVG 1.771,1.5 2.229,1.698 0.458,0.198 10 false E2G
*1 Mass Air Flow Meter Sub-assembly *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
- -



b.

Connect terminals 4 (THA) and 2 (E2G) of the mass air flow meter sub-assembly wire harness side connector.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1
50003 372 613

d.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

5.CONFIRM ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A335969C07
0.156,0.094 0.469,0.292 0.313,0.198 10 false *1 2.323,0.094 2.635,0.292 0.313,0.198 10 false *2 1.302,0.698 1.615,0.896 0.313,0.198 10 false THA 2.333,0.688 2.646,0.885 0.313,0.198 10 false THA 2.354,1.292 2.667,1.49 0.313,0.198 10 false EVG 1.302,1.292 1.615,1.49 0.313,0.198 10 false E2G
*1 Mass Air Flow Meter Sub-assembly
*2 ECM


Disconnect the mass air flow meter sub-assembly connector.


b.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1
50003 372 613

c.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

7.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
7.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch to ON and wait for 1 second or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED