Refer to DTC P004518.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P004518
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P029907 | Turbocharger/Supercharger "A" Underboost Condition Mechanical Failure | The pressure is 55 kPa below the Target Boost Pressure for 20 seconds at an engine speed of 2800 to 4400 rpm. (1 trip detection logic) |
Turbocharger sub-assembly | Comes on | SAE Code: P0299 |
| DTC No. | Data List |
|---|---|
| P029907 |
·
Target VN Turbo Position Bank 1
·
Actual VN Turbo Position Bank 1
·
Target VN Turbo 2 Position*
·
Actual VN Turbo 2 Position*
|
If DTC P029907 is stored due to the variable nozzle being stuck open, the following symptoms may appear:
Lack of power
Vehicle surge or hesitation under light or medium load
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P029907 | Accelerate vehicle with accelerator depressed halfway or more starting from a speed of 120 km/h (75 mph) or more for 2 minutes (make sure gear is fixed and does not change) |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
When replacing the turbocharger sub-assembly, calibrate the VN turbo offset voltage value and initialize the learning values after replacement.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The state of the problem symptom can be determined by comparing the Data List items "Intake Manifold Absolute Pressure" and "Target Boost Pressure" while accelerating at a medium to high engine speed.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P029907 is output | A |
| DTC P029907 and other DTCs are output | B |
A
B
Perform the Active Test.
Bank 1:
Enter the following menus: Powertrain / Engine / Active Test / Test the Turbo Charger Step Motor Bank 1 / Data List / Target VN Turbo Position Bank 1 and Actual VN Turbo Position Bank 1.
| Active Test Display |
|---|
| Test the Turbo Charger Step Motor Bank 1 |
| Data List Display |
|---|
| Target VN Turbo Position Bank 1 |
| Actual VN Turbo Position Bank 1 |
Bank 2:
Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo 2 Position / Data List / Target VN Turbo 2 Position and Actual VN Turbo 2 Position.
| Active Test Display |
|---|
| Control the VN Turbo 2 Position |
| Data List Display |
|---|
| Target VN Turbo 2 Position |
| Actual VN Turbo 2 Position |
While changing the Active Test value to 10, 20, 30, 40, 30, 20 and 10%, check that Actual VN Turbo Position smoothly changes to the set opening amount.
When moving the vanes toward the fully closed position, make sure that Actual VN Turbo Position does not become 5% or less.
The Actual VN Turbo Position value follows the Target VN Turbo Position.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the malfunctioning turbocharger sub-assembly.
Replace the No. 1 Turbocharger sub-assembly.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL
Replace the No. 2 Turbocharger sub-assembly.
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL