Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P24A571  Exhaust Gas Recirculation Cooler Bypass Control Stuck/Open Bank 1 Actuator Stuck  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P24A571 Exhaust Gas Recirculation Cooler Bypass Control Stuck/Open Bank 1 Actuator Stuck Either of the following conditions is met:
·

A change in the opening angle of the EGR cooler bypass valve of less than the specified value (1.75%) continues for 22 seconds or more, even if the drive duty ratio of the EGR cooler bypass valve exceeds the threshold (-80 to 80%) with the ignition switch turned to ON or the engine running

·

The drive duty ratio of the EGR cooler bypass valve exceeds the threshold (-88 to 88%) with the ignition switch turned to ON or the engine running, and the condition that a motor current value of the specified value (1 A) or more continues for 0.5 seconds occurs the specified number of times (39.5 seconds or more in real time).


(1 trip detection logic)
·

No. 2 EGR valve assembly (EGR cooler bypass valve) stuck

·

No. 2 EGR valve assembly (EGR cooler bypass valve) does not move smoothly

·

No. 2 EGR valve assembly (EGR cooler bypass valve) deposit


Comes on SAE Code: P24A5

Related Data List
DTC No. Data List
P24A571
·

EGR Cooler Bypass Valve Request Position

·

EGR Cooler Bypass Valve Position

·

EGR Cooler Bypass Valve Duty Ratio

·

EGR Cooler Bypass Valve Motor Current

·

EGR Temperature B1S1



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24A571 Check that "EGR Cooler Bypass Valve Position" follows "EGR Cooler Bypass Valve Request Position" when performing the Active Test.

CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the electric EGR control valve assembly, No. 2 EGR valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24A571)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P24A571 is output A
DTC P24A571 and other DTCs are output B


HINT:

If any DTCs other than P24A571 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR COOLER BYPASS CONTROL VALVE)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR COOLER BYPASS CONTROL VALVE)
a.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve / Data List / EGR Cooler Bypass Valve Request Position and EGR Cooler Bypass Valve Position.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Cooler Bypass Control Valve
Data List Display
EGR Cooler Bypass Valve Request Position
EGR Cooler Bypass Valve Position
50004 372 42024 1451,1452

b.

Read the value displayed on the GTS when the Active Test was performed

OK:

The EGR Cooler Bypass Valve Position value follows the EGR Cooler Bypass Valve Request Position value.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR COOLER BYPASS CONTROL VALVE)

NG

6.REPLACE NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE)
3.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR COOLER BYPASS CONTROL VALVE)
a.

Remove the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL


b.

Reconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve.

Powertrain > Engine > Active Test
Tester Display
Control the EGR Cooler Bypass Control Valve
50004 372 42024

f.

Check if the valve of the No. 2 EGR valve assembly (EGR cooler bypass valve) opens/closes when an Active Test is performed.

OK:

The valve opens/closes.



Result:
Proceed to
OK
NG


g.

Reinstall the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION



OK

4.CHECK FOR DEPOSIT (NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE))

NG

6.REPLACE NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE)
4.CHECK FOR DEPOSIT (NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE))
a.

Remove the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL


b.

Visually check the No. 2 EGR valve assembly (EGR cooler bypass valve) for deposits. If there are deposits, clean the No. 2 EGR valve assembly (EGR cooler bypass valve).

NOTICE:
·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the No. 2 EGR valve assembly (EGR cooler bypass valve), use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the No. 2 EGR valve assembly (EGR cooler bypass valve), care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the valve.




c.

Reinstall the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Cooler Bypass Control Valve / Data List / EGR Cooler Bypass Valve Request Position and EGR Cooler Bypass Valve Position.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Cooler Bypass Control Valve
Data List Display
EGR Cooler Bypass Valve Request Position
EGR Cooler Bypass Valve Position
50004 372 42024 1451,1452

d.

Check that "EGR Cooler Bypass Valve Position" follows "EGR Cooler Bypass Valve Request Position" when performing the Active Test.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

f.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE)
a.

Replace the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Before replacing the No. 2 EGR valve assembly (EGR cooler bypass valve), check the connections of the wire harness and connectors. If there is any abnormality, replace or repair the wire harness or connector.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED