Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P249211  Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit Low Bank 1 Circuit Short to Ground  P249215  Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit High Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P245A18.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P245A18

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P249211 Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit Low Bank 1 Circuit Short to Ground EGR cooler bypass valve position sensor output is below 0.13 V for 2 seconds.
(1 trip detection logic)
·

No. 2 EGR valve assembly (EGR cooler bypass valve)

·

ECM


Comes on SAE Code: P2494
P249215 Exhaust Gas Recirculation Cooler Bypass Position Sensor Circuit High Bank 1 Circuit Short to Battery or Open EGR cooler bypass valve position sensor output is higher than 4.89 V for 2 seconds.
(1 trip detection logic)
·

No. 2 EGR valve assembly (EGR cooler bypass valve)

·

ECM


Comes on SAE Code: P2495

Related Data List
DTC No. Data List
P249211
P249215
·

EGR Cooler Bypass Valve Position

·

EGR Cooler Bypass Valve Position Sensor



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P249211
P249215
Ignition switch ON for 2 seconds or more

WIRING DIAGRAM

A490898E02
5.74,3.76 6.198,3.958 0.458,0.198 10 false C138 5.406,0.75 6.094,0.948 0.688,0.198 10 false VCEC 5.406,1.25 6.021,1.563 0.615,0.313 10 false ECBA 5.406,1.781 5.865,1.979 0.458,0.198 10 false EECB 5.208,2.302 5.417,2.531 0.208,0.229 10 false 4 2.167,0.771 2.625,0.969 0.458,0.198 10 false 2 1.698,2.969 2.458,3.354 0.76,0.385 10 false ECM- 1.708,2.448 2.469,2.74 0.76,0.292 10 false ECM+ 1.688,1.813 2.313,2.125 0.625,0.313 10 false EECB 1.698,1.281 2.302,1.531 0.604,0.25 10 false ECBA 1.698,0.771 2.385,1.021 0.688,0.25 10 false VCEC 0.208,3.667 1.052,3.906 0.844,0.24 10 false C130 0.188,3.823 4.406,4.49 4.219,0.667 10 false No. 2 EGR Valve Assembly (EGR Cooler Bypass Valve) 5.74,3.917 6.458,4.25 0.719,0.333 10 false ECM 5.406,2.958 6.01,3.188 0.604,0.229 10 false ECM- 5.406,2.448 5.938,2.688 0.531,0.24 10 false ECM+ 2.177,1.813 2.385,2.042 0.208,0.229 10 false 3 2.177,2.323 2.385,2.552 0.208,0.229 10 false 6 2.167,2.844 2.375,3.073 0.208,0.229 10 false 5 2.177,1.281 2.385,1.51 0.208,0.229 10 false 4 5.146,2.802 5.677,3.031 0.531,0.229 10 false 23 5.146,0.75 5.656,0.969 0.51,0.219 10 false 91 5.125,1.229 5.583,1.427 0.458,0.198 10 false 68 5.146,1.792 5.604,1.99 0.458,0.198 10 false 90

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE) - ECM)
a.

Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C130,C138)Location & Routing

Click Connector(C130)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 EGR Valve Assembly

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C130-2 (VCEC) - C138-91 (VCEC) Always Below 1 Ω
C130-4 (ECBA) - C138-68 (ECBA) Always Below 1 Ω
C130-3 (EECB) - C138-90 (EECB) Always Below 1 Ω
C130-2 (VCEC) or C138-91 (VCEC) - Body ground and other terminals Always 10 kΩ or higher
C130-4 (ECBA) or C138-68 (ECBA) - Body ground and other terminals Always 10 kΩ or higher
C130-3 (EECB) or C138-90 (EECB) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C130)Location & Routing

Click Connector(C130)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 EGR Valve Assembly

C130-2 (VCEC) - C130-3 (EECB) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK ECM

NG

6.REPLACE ECM
3.CHECK ECM
a.

Disconnect the No. 2 EGR valve assembly (EGR cooler bypass valve) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C130)Location & Routing

Click Connector(C130)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>No. 2 EGR Valve Assembly

C130-2 (VCEC) - C130-4 (ECBA) Ignition switch off No short or no open circuit
C130-4 (ECBA) - C130-3 (EECB) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE)

NG

5.REPLACE ECM
4.REPLACE NO. 2 EGR VALVE ASSEMBLY (EGR COOLER BYPASS VALVE)
a.

Replace the No. 2 EGR valve assembly (EGR cooler bypass valve).

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds.


c.

Turn the ignition switch to ON and wait for 2 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END