Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P261029  ECM/PCM Engine Off Timer Performance Signal Invalid  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A485559E02
0.167,1.854 1.083,2.073 0.917,0.219 10 false from Battery 3.656,0.979 4.677,1.177 1.021,0.198 10 false ENG-IGP NO. 1 1.146,3.573 2.177,3.823 1.031,0.25 10 false EFI MAIN NO. 1 2.125,3.938 2.844,4.198 0.719,0.26 10 false EFI NO. 2 2.719,4.156 3.875,4.375 1.156,0.219 10 false EFI MAIN NO. 1 2.76,1.979 4.573,2.49 1.813,0.51 10 false from Certification ECU (Smart Key ECU Assembly) 4.51,0.688 4.958,0.927 0.448,0.24 10 false IGP 5.063,1.083 6.021,1.552 0.958,0.469 10 false Soak Timer IC 5.073,2.771 5.969,3.208 0.896,0.438 10 false Power Source IC 5.156,3.542 5.885,4.021 0.729,0.479 10 false Main Relay Control IC 5.76,4.323 6.375,4.667 0.615,0.344 10 false ECM 4.406,3.635 4.854,3.875 0.448,0.24 10 false MREL 4.604,2.833 4.854,3.063 0.25,0.229 10 false +B 3.813,3.135 4.729,3.406 0.917,0.271 10 false EFI-B NO. 1 2.792,1.563 3.521,1.802 0.729,0.24 10 false IGP NO. 2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P261029 ECM/PCM Engine Off Timer Performance Signal Invalid ECM internal malfunction.
(2 trip detection logic).
ECM Comes on SAE Code: P2610

MONITOR DESCRIPTION

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:
·

DTC P261029 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P261029)
2.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P261029)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P261029 is output A
DTCs are not output B




A

3.REPLACE ECM

B

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and wait for 10 minutes or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END