The Intake Air Temperature Sensor (for intercooler Inlet) detects the intake air temperature before the intake air passes through the turbo charger. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THCA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THCA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P009511 | Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Ground | Short in intake air temperature sensor (for intercooler inlet) circuit for 3 seconds. (2 trip detection logic) |
·
Short in intake air temperature sensor (for intercooler inlet) circuit
·
Intake air temperature sensor (for intercooler inlet)
·
ECM |
Comes on | SAE Code: P0097 |
| P009515 | Intake Air Temperature Sensor 2 Bank 1 Circuit Short to Battery or Open | Open in intake air temperature sensor (for intercooler inlet) circuit for 3 seconds. (2 trip detection logic) |
·
Open in intake air temperature sensor (for intercooler inlet) circuit
·
Intake air temperature sensor (for intercooler inlet)
·
ECM |
Comes on | SAE Code: P0098 |
When any of DTCs are stored, check the intake air temperature sensor (for intercooler inlet) by entering the following menus on the GTS: Powertrain / Engine / Data List / Intake Air Temperature B1S2.
| Temperature Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 215°C (419°F) or more | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P009511 P009515 |
Ignition switch ON for 3 seconds or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S2 |
Same value as the actual inlet air temperature.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) or more | B |
| OK (same as air temperature near intake manifold) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 215°C (419°F) or more.
A
B
C
| *1 | Intake Air Temperature Sensor (For Intercooler Inlet) |
| *2 | ECM |
| *a | Front view of wire harness connector (to Intake Air Temperature Sensor (For Intercooler Inlet)) |
Disconnect the intake air temperature sensor (for intercooler inlet) connector.
Connect terminals 1 (T3) and 2 (ET3) of the intake air temperature sensor (for intercooler inlet) wire harness side connector.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S2 |
215°C (419°F) or higher
Reconnect the intake air temperature sensor (for intercooler inlet) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (for intercooler inlet).
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (for intercooler inlet) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C114,C138)Location & Routingewd_type=routing;type=c,c;code=C114,C138 |
||
| C114-1 (T3) - C138-102 (THCA) | Always | Below 1 Ω |
| C114-2 (ET3) - C138-125 (ETCA) | Always | Below 1 Ω |
Reconnect the intake air temperature sensor (for intercooler inlet) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Intake Air Temperature Sensor (For Intercooler Inlet) |
| *2 | ECM |
Disconnect the intake air temperature sensor (for intercooler inlet) connector.
Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S2.
Read the value.
| Tester Display |
|---|
| Intake Air Temperature B1S2 |
-40°C (-40°F)
Reconnect the intake air temperature sensor (for intercooler inlet) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (for intercooler inlet).
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 1 second or more.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (for intercooler inlet) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C114,C138)Location & Routingewd_type=routing;type=c,c;code=C114,C138 |
||
| C114-1 (T3) or C138-102 (THCA) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor (for intercooler inlet) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT