The EGR gas temperature sensor is installed to the intake pipe between the electric EGR control valve assembly and intake manifold, and monitors the temperature of exhaust gas introduced into the intake manifold.
A thermistor built into the EGR gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The EGR gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the EGR gas temperature sensor from terminal THGO via resistor R.
Resistor R and the EGR gas temperature sensor are connected in series. When the resistance value of the EGR gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THGO also changes.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P040A11 | Exhaust Gas Recirculation Temperature Sensor "A" Circuit Low Circuit Short to Ground | EGR gas temperature sensor output voltage is below 0.11 V for 3 seconds or more. (1 trip detection logic) |
·
Open or short in EGR gas temperature sensor circuit
·
EGR gas temperature sensor
·
ECM |
Comes on | SAE Code: P040C |
| P040A15 | Exhaust Gas Recirculation Temperature Sensor "A" Circuit High Circuit Short to Battery or Open | EGR gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses
·
Engine is running
·
Coolant temperature is 60°C (140°F) or higher |
·
Open or short in EGR gas temperature sensor circuit
·
EGR gas temperature sensor
·
ECM |
Comes on | SAE Code: P040D |
| DTC No. | Data List |
|---|---|
| P040A11 P040A15 |
EGR Temperature B1S1 |
When DTC P040A11 and P040A15 is output, check the exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1" using the GTS.
| Condition | EGR Temperature B1S1 | EGR Gas Temperature Sensor Condition |
|---|---|---|
| Idling with warm engine | Constant at between 50 and 700°C (122 and 1292°F) | Normal |
| 0°C (32°F) | Open circuit | |
| 980°C (1600°F) | Short circuit |
The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P040A11 | Ignition switch ON for 3 seconds or more |
| P040A15 | Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1.
| Tester Display |
|---|
| EGR Temperature B1S1 |
Read the value.
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
| Temperature Displayed | Proceed to |
|---|---|
| 0°C (32°F) (After warming up the engine) | A |
| 980°C (1600°F) or higher | B |
| Same as the actual exhaust gas temperature | C |
If there is a short circuit, the GTS will indicate 0°C (32°F).
If there is an open circuit, the GTS will indicate 980°C (1600°F).
A
B
C
| *1 | EGR Gas Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector (to EGR Gas Temperature Sensor) |
Disconnect the EGR gas temperature sensor connector.
Connect terminals 1 (E2) and 2 (THEG) of the EGR gas temperature sensor connector on the wire harness side.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / EGR Temperature B1S1.
| Tester Display |
|---|
| EGR Temperature B1S1 |
Read the value.
980°C (1600°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the EGR gas temperature sensor.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for EGR)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the EGR gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C172,C138)Location & Routingewd_type=routing;type=c,c;code=C172,C138 |
||
| C172-2 (THEG) - C138-104 (THGO) | Always | Below 1 Ω |
| C172-1 (E2) - C138-127 (ETGO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and turn the GTS on.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | EGR Gas Temperature Sensor |
| *2 | ECM |
Disconnect the EGR gas temperature sensor connector.
Enter the following menus: Powertrain / Engine / Data List / EGR Temperature B1S1.
| Tester Display |
|---|
| EGR Temperature B1S1 |
Read the value.
0°C (32°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the EGR gas temperature sensor.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR (for EGR)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the EGR gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C172,C138)Location & Routingewd_type=routing;type=c,c;code=C172,C138 |
||
| C172-2 (THEG) or C138-104 (THGO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT