Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P05A212  Active Grille Air Shutter "A" Circuit Short to Battery  


DESCRIPTION

Refer to DTC P059A71.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P059A71

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P05A212 Active Grille Air Shutter "A" Circuit Short to Battery Short to +B in swing grille actuator assembly or grille shutter motor drive circuit for 7.86 seconds or more (1 trip detection logic). Radiator shutter assembly Does not come on SAE Code: P05A4

MONITOR DESCRIPTION

When the swing grille actuator assembly detects that there is a grille shutter circuit malfunction, a DTC request is sent to the ECM and the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P05A212 Ignition switch ON for 10 second or more

CAUTION / NOTICE / HINT

NOTICE:

In order to ensure safety, before performing troubleshooting or removing the radiator shutter assembly, change the grille shutter control mode to maintenance mode.


HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (SWITCH GRILLE SHUTTER CONTROL MODE)
a.

Turn the ignition switch off and wait for 30 seconds or more.


b.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

Result:
Proceed to
NEXT



NEXT

2.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
2.PERFORM UTILITY USING GTS (GRILLE SHUTTER INITIALIZATION)
a.

According to the display on the GTS, perform initialization (nominal torque).

Powertrain > Engine > Utility
Tester Display
Grille Shutter Initialization
50005 372 5673

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (DTC P05A212)
4.CHECK DTC OUTPUT (DTC P05A212)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P05A212 is not output A
P05A212 is output B



HINT:

Perform "Switch Grille Shutter Control Mode and Grille Shutter Initialization" after replacing the radiator shutter assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION



A

5.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)

B

REPLACE RADIATOR SHUTTER ASSEMBLY

5.READ VALUE USING GTS (GRILLE SHUTTER CONTROL MODE)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Powertrain > Engine > Utility
Tester Display
Switch Grille Shutter Control Mode
50005 372 5672

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Grille Shutter Control Mode
50003 372 1304
Standard:
GTS Display Specified Condition
Grille Shutter Control Mode Normal


Result:
Proceed to
NEXT




NEXT

END