| ● | Non-reusable part | - | - |
| *1 | DRIVE PINION WASHER | *2 | PLATE WASHER |
| *3 | FRONT DIFFERENTIAL SUPPORT ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
1.INSPECT DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH
Using SST and a dial indicator, measure the differential ring gear backlash.
0.17 to 0.27 mm (0.00670 to 0.0106 in.)
If the backlash is not as specified, adjust the side bearing preload or perform repairs as necessary.
Perform the measurement at 3 or more positions around the circumference of the differential ring gear.
41204D 2.INSPECT FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
| *a | 33 mm (1.30 in.) | - | - |
Using a dial indicator, measure the runout of the front drive pinion companion flange vertically and laterally.
| Item | Specified Condition |
|---|---|
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.13 mm (0.00512 in.) |
If the runout is more than the maximum, replace the front drive pinion companion flange.
41321 3.REMOVE DIFFERENTIAL EXTENSION FLANGE TUBE
41304F 5.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH
Using a snap ring pliers, remove the snap ring.
Remove the differential side gear shaft sub-assembly RH from the front differential tube assembly.
41304L 6.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT BEARING RH
Using a snap ring expander, remove the snap ring.
Using SST, a brass bar and a press, press out the front differential side gear shaft bearing RH.
Do not damage the front differential side gear shaft bearing RH.
Do not drop the differential side gear shaft sub-assembly RH.
43420H 7.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST, tap out the differential side gear shaft oil seal LH.
41204E 8.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT
| *a | Turn | *b | Hold |
Using SST and a hammer, loosen the staked part of the front drive pinion companion flange nut.
Using SST to hold the companion flange, remove the front drive pinion companion flange nut.
41204D 9.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
| *a | Turn | *b | Hold |
Using SST, remove the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
41214C 11.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
12.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER
Remove the 14 bolts.
Using a plastic-faced hammer, tap out the bearing retainer and front differential support assembly.
41301L 13.REMOVE FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY
14.REMOVE DIFFERENTIAL DRIVE PINION
Using a press, press out the drive pinion.
41211A 15.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER)
41231F 16.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
41211B 17.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)
Using SST and a press, press out the rear drive pinion front taperd roller bearing (inner race) from the drive pinion.
Do not drop the differential drive pinion.
If the drive pinion or ring gear is damaged, replace them as a set.
41211A 18.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING (OUTER)
| *a | Turn | *b | Hold |
Using SST, remove the front drive pinion front radial ball bearing (outer).
Align the claw part of SST with the groove part of front drive pinion front radial ball bearing (outer) and remove it.
41115F 19.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
41211B 20.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (OUTER)
Using SST, remove the front drive pinion rear tapered roller bearing (outer) and drive pinion washer.
41311A 21.REMOVE FRONT DIFFERENTIAL CASE BEARING (OUTER)
|
|
Using SST and a press, press out the front differential case bearing (outer) and plate washer from the differential side bearing retainer.
If the bearing is damaged during removal, replace it.
Using SST and a press, press out the front differential case bearing (outer) and plate washer from the differential carrier.
If the bearing is damaged during removal, replace it.
22.REMOVE FRONT DIFFERENTIAL UNION
41183C 23.REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR
24.REMOVE DIFFERENTIAL RING GEAR
| *a | Matchmark | - | - |
Place matchmarks on the differential ring gear and differential case.
Remove the 12 bolts.
Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case assembly.
41311A 25.REMOVE FRONT DIFFERENTIAL CASE BEARING (INNER)
| *a | Turn | *b | Hold |
Using SST, remove the 2 front differential case bearings (inner) from the differential case.
Attach the claws of SST to the notch in the differential case assembly to secure SST.
If the front differential case bearing (inner) is removed sufficiently and the part remains on the case side, use SST as shown in the illustration and remove the relevant part.
41111D 26.REMOVE FRONT DIFFERENTIAL CARRIER STRAIGHT PIN