Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL
RM38G0E _52 Drivetrain _100455 AXLE AND DIFFERENTIAL _0485436 FRONT DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential carrier oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)


NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) -
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C03
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


Be sure to perform this procedure with several people as the front differential carrier assembly is very heavy.

·

Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1.DRAIN DIFFERENTIAL OIL

Hide 84546 4.REMOVE NO. 1 4 WHEEL DRIVE POSITION SWITCH (w/ Differential Lock)

Hide 82H24B 5.REMOVE WIRING HARNESS CONNECTOR (w/ Differential Lock)

Hide 41204D 7.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 41101D 8.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C457981N01
1.76,1.01 1.76,0.302 1.76,0.302 1.927,0.302 false 1.979,0.219 2.458,0.427 0.479,0.208 10 false SST

Using SST, remove the front differential carrier oil seal.

SST
09308-10010  


Hide 41141L 10.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Hide 41211B 13.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING (INNER)

Hide 41231F 14.REPLACE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41141L 17.INSTALL FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

Hide 41211A 18.INSTALL FRONT DRIVE PINION FRONT RADIAL BALL BEARING (INNER)

Hide 41101D 20.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL

a.

Using SST, Install the front differential carrier oil seal.

SST
09513-36040  

Standard rear differential carrier oil seal depth:

5.6 to 6.6 mm (0.221 to 0.0259 in.)


C458490C01
1.958,0.896 2.375,0.896 true 2.417,0.802 2.813,1.021 0.396,0.219 10 false SST 5.448,0.667 5.76,0.865 0.313,0.198 10 false *a
*a Front Differential Carrier Oil Seal Depth - -



b.

Apply MP grease to the lip of the front differential carrier oil seal.


Hide 41204D 21.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

Hide 82H24B 26.INSTALL WIRING HARNESS CONNECTOR (w/ Differential Lock)

Hide 84546 27.INSTALL NO. 1 4 WHEEL DRIVE POSITION SWITCH (w/ Differential Lock)

Hide 29.ADD DIFFERENTIAL OIL