When the STA signal detected by the ECM and by the engine stop and start ECU do not match, the engine stop and start ECU stores DTC P061562 and blinks the stop and start cancel indicator.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Note |
|---|---|---|---|---|---|
| P061562 | Starter Relay Signal Compare Failure | Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·
Normal communication with the ECM.
·
The STA signal detected by the ECM and STA2 signal detected by the engine stop and start ECU do not match. |
·
Wire harness or connector
·
ST NO. 1 relay*1
·
ST NO. 2 relay*2
·
Engine stop and start ECU
·
Starter assembly
·
ECM |
Blinks | SAE Code: P0615 |
*1: for F33A-FTV
*2: for V35A-FTS
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
Check that no DTCs are output.
STOP AND START SYSTEM OPERATION CHECK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
Refer to DTC P061519.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P061519
Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
Enter the following menus: Powertrain / Stop and Start / Data List / Engine Starter Signal.
| Tester Display |
|---|
| Engine Starter Signal |
Read the values displayed on the GTS when the ignition switch is ON and START.
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Engine Starter Signal | Ignition switch ON | OFF |
| Ignition switch START | ON |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for V35A-FTS) |
B |
| NG (for F33A-FTV) |
C |
A
B
C
Enter the following menus: Powertrain / Engine / Data List / Starter SW.
Read the values displayed on the GTS when the ignition switch is ON and START.
| Tester Display |
|---|
| Starter SW |
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Starter SW | Ignition switch ON | OFF |
| Ignition switch START | ON |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for V35A-FTS) |
B |
| NG (for F33A-FTV) |
C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B1)Location & Routingewd_type=routing;type=c;code=B1 |
||
| B1-34 (STA) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B1-34 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B70)Location & Routingewd_type=routing;type=c;code=B70 |
||
| B70-25 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B70-25 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38,B1)Location & Routingewd_type=routing;type=c,c;code=B38,B1 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=23 |
||
| B38-23 (STA2) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B1-34 (STA) - ST NO. 2 relay terminal 2 | Always | Below 1 Ω |
| B38-23 (STA2) - B1-34 (STA) | Always | Below 1 Ω |
| B38-23 (STA2) - Body ground | Always | 10 kΩ or higher |
| B1-34 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 2 relay.
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 2 relays from the NO. 2 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B70,B38)Location & Routingewd_type=routing;type=c,c;code=B70,B38 |
||
| B70-25 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B38-21 (STA) - B70-25 (STA) | Always | Below 1 Ω |
| B70-25 (STA) - Body ground | Always | 10 kΩ or higher |
| B38-21 (STA) - Body ground | Always | 10 kΩ or higher |
| ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST NO. 1 relay.
Click hereEngine / Hybrid System>F33A-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relays from the NO. 4 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG