The park/neutral position switch assembly detect the shift lever position and send signals to the TCM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic). |
·
Wire harness or connector
·
Park/neutral position switch assembly
·
TCM |
Comes on | DTC stored | SAE: P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic):
·
P or N input signal
·
R input signal
·
D input signal |
·
Wire harness or connector
·
Park/neutral position switch assembly
·
TCM |
Comes on | DTC stored | SAE: P0705 |
| Vehicle Condition | ||||||
|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | ||
| Diagnostic Condition | Ignition switch is ON | ○ | ○ | ○ | ○ | ○ |
| Malfunction Condition | P input signal is ON | ○ | ○ | - | - | - |
| R input signal is ON | ○ | - | ○ | - | ○ | |
| N input signal is ON | - | - | ○ | ○ | - | |
| D input signal is ON | - | ○ | - | ○ | ○ | |
| Duration | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
DTC P070562 is stored when any of the above detection patterns is met.
These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch assembly detects the shift lever position and sends a signal to the TCM. For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (P, R, N or D).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will then illuminate the MIL and store a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Wait with the shift lever in each position (P, R, N or D) for 60 seconds or more with the ignition switch ON.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P070513 or P070562.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transmission are replaced.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/neutral position switch assembly status | OFF or ON |
·
OFF: Shift lever not in P
·
ON: Shift lever in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/neutral position switch assembly status | OFF or ON |
·
OFF: Shift lever not in R
·
ON: Shift lever in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch assembly status | OFF or ON |
·
OFF: Shift lever not in N
·
ON: Shift lever in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (D Range) | Park/neutral position switch assembly status | OFF or ON |
·
OFF: Shift lever not in D, M, "+" or "-"
·
ON: Shift lever in D, M, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Tester Display |
|---|
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34)Location & Routingewd_type=routing;type=c;code=C34 |
||
| C34-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| C34-2 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34)Location & Routingewd_type=routing;type=c;code=C34 |
||
| C34-2 (RB) - C34-6 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| C34-2 (RB) - C34-1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| C34-2 (RB) - C34-9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| C34-2 (RB) - C34-7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in D, M, "+" or "-" | 10 kΩ or higher | |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the park/neutral position switch assembly connector.
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34,C36)Location & Routingewd_type=routing;type=c,c;code=C34,C36 |
||
| C34-6 (PL) - C36-15 (P) | Always | Below 1 Ω |
| C34-1 (RL) - C36-34 (R) | Always | Below 1 Ω |
| C34-9 (NL) - C36-16 (N) | Always | Below 1 Ω |
| C34-7 (DL) - C36-35 (D) | Always | Below 1 Ω |
| C34-6 (PL) or C36-15 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-1 (RL) or C36-34 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-9 (NL) or C36-16 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| C34-7 (DL) or C36-35 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT