This DTC is stored when the combination meter assembly detects a No. 2 fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B150113 | Sub Fuel Sender Circuit Open | When IG voltage is 9.5 V or more and the following condition is detected:
·
Average input signal of fuel sender gauge assembly is 630 Ω or more 3 times consecutively |
·
Harness or connector
·
No. 2 fuel sender gauge assembly
·
Fuel tank vent tube assembly
·
Combination meter assembly |
- |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>INSPECTION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
Remove the fuel tank vent tube assembly.
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (FV2) - B-1 | Always | Below 1 Ω |
| A-2 (FE2) - B-2 | Always | Below 1 Ω |
| A-3 (FR2) - B-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for Double Tank Type)>REMOVAL
Disconnect the V10 No. 2 fuel tank vent tube assembly connector.
Disconnect the I5 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(V10,I5)Location & Routingewd_type=routing;type=c,c;code=V10,I5 Click Connector(V10)Body>Differential Wire / Frame Wire>Fuel Pump (Fuel Tank Sub-Assembly)ewd_type=component;type=c;code=V10;pinno=3,2,1 |
||
| V10-3 (FR2) - I5-8 (FR) | Always | Below 1 Ω |
| V10-2 (FE2) - I5-34 (FE) | Always | Below 1 Ω |
| V10-1 (FV2) - I5-24 (FV) | Always | Below 1 Ω |
| I5-8 (FR) - Body ground | Always | 10 kΩ or higher |
| I5-34 (FE) - Body ground | Always | 10 kΩ or higher |
| I5-24 (FV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG