If an abnormal operation that may lead to a malfunction of the steering lock ECU (steering lock actuator with ECU assembly), or abnormal vehicle speed information is detected by the certification ECU (smart key ECU assembly), a system malfunction message is displayed on the multi-information display.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator with ECU assembly), refer to Service Bulletin.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC is output. | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sensor Malfunction History | History of malfunction of position sensor in steering lock ECU (steering lock actuator with ECU assembly) (DTC B278196 is stored) | OK or NG | OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator with ECU assembly) does not exist. NG: History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator with ECU assembly) being on exists. (Under normal operation, neither sensor is on.) |
When NG is displayed, either the position sensor in the steering lock ECU (steering lock actuator with ECU assembly) or the assembly itself may be malfunctioning. |
| Tester Display |
|---|
| Sensor Malfunction History |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Power Tilt and Power Telescopic Steering Column:
for Manual Tilt and Manual Telescopic Steering Column:
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Running Condition (Line) | Vehicle being driven or stopped | Stop or Driving | Stop: Vehicle stopped Driving: Vehicle being driven at 5 km/h (3 mph) or more |
- |
| Tester Display |
|---|
| Vehicle Running Condition (Line) |
The GTS display changes correctly in response to the vehicle condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I49)Location & Routingewd_type=routing;type=c;code=I49 |
||
| I49-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I49)Location & Routingewd_type=routing;type=c;code=I49 |
||
| I49-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator with ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I49)Location & Routingewd_type=routing;type=c;code=I49 |
||
| I49-3 (IGE) - I49-1 (GND) |
Steering lock motor operating when all conditions met, and then door opened:
-
The steering is unlocked.
-
The ignition switch is off.
-
The shift lever is in P. |
11 to 14 V → Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for Power Tilt and Power Telescopic Steering Column:
for Manual Tilt and Manual Telescopic Steering Column:
NG
Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I49,I39)Location & Routingewd_type=routing;type=c,c;code=I49,I39 |
||
| I49-3 (IGE) - I39-24 (SLR+) | Always | Below 1 Ω |
| I49-3 (IGE) or I39-24 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.
| *a | Component with harness connected (Steering Lock ECU (Steering Lock Actuator with ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I49)Location & Routingewd_type=routing;type=c;code=I49 |
||
| I49-3 (IGE) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Power Tilt and Power Telescopic Steering Column:
for Manual Tilt and Manual Telescopic Steering Column: