Home › Steering › STEERING COLUMN › TILT AND TELESCOPIC MANUAL SWITCH › from 2021.07
RM38G0E _55 Steering _100923 STEERING COLUMN _0469203 TILT AND TELESCOPIC MANUAL SWITCH A

STEERING COLUMN  TILT AND TELESCOPIC MANUAL SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456097N01
6.583,0.219 6.875,0.219 true 4.573,3.25 4.917,3.5 4.917,3.5 5.083,3.5 true 1.229,2.104 1.646,2.104 true 6.604,0.688 6.813,0.688 true 5.073,2.677 5.385,2.875 0.313,0.198 10 false x 3 6.094,0.073 6.656,0.438 0.563,0.365 18 false 1, 2 5.5,3.385 5.833,3.719 0.333,0.333 18 false 4 6.406,0.531 6.74,0.865 0.333,0.333 18 false 3 1,1.969 1.333,2.302 0.333,0.333 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
3 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 LOWER STEERING COLUMN COVER SUB-ASSEMBLY 45024 (Click here) - -
5 TILT AND TELESCOPIC SWITCH 89235A (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the tilt and telescopic manual switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

Z101186

Click here(Click here)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 45024 4.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C456098C01
0.771,0.094 1.052,0.448 0.281,0.354 18 false i 3.563,0.115 3.865,0.396 0.302,0.281 18 false ii 1.958,2.042 2.26,2.323 0.302,0.281 18 false iii
V113146

Push Area
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)
V113149

Remove in this Direction (3)


i.

Turn the steering wheel and remove the 3 screws.


ii.

Press the part in the direction of the arrow shown in the illustration to detach the claw.


iii.

Detach the 2 claws and remove the lower steering column cover in the direction of the arrow shown in the illustration.

NOTICE:

Do not damage the tilt and telescopic switch.




Hide 89235A 5.REMOVE TILT AND TELESCOPIC SWITCH

a.
C456728C01
1.25,1.979 1.594,1.688 1.594,1.688 1.698,1.688 true 1.75,1.604 2.063,1.802 0.313,0.198 10 false *a 0.385,0.115 0.667,0.469 0.281,0.354 18 false i 4.208,0.135 4.698,0.448 0.49,0.313 18 false ii, iii
*a Slider - -


i.

Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.

HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



ii.

Disconnect the tilt and telescopic connector from the tilt and telescopic switch.


iii.

Disengage the claw and pull out the tilt and telescopic switch.