Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100628 SEAT _0467517 CLIMATE CONTROL SEAT SYSTEM J

SEAT  CLIMATE CONTROL SEAT SYSTEM  Climate Control System does not Operate on Rear Left Side  


DESCRIPTION

The air conditioning amplifier assembly receives ventilation volume switch signals when the ignition switch is ON, and then transmits airflow amount signals to each seat climate blower.

WIRING DIAGRAM

C450696E09
0.479,1.208 2.677,1.604 2.198,0.396 10 false Cooler Control Switch Assembly 5.458,4.146 7.021,4.75 1.563,0.604 10 false Air Conditioning Amplifier Assembly 5.458,3.948 5.99,4.115 0.531,0.167 10 false I31 5.479,1.656 6.01,1.823 0.531,0.167 10 false 22 5.781,1.76 6.385,2.031 0.604,0.271 10 false SV2L 4.438,1.792 4.969,1.958 0.531,0.167 10 false SING 3.917,1.781 4.448,1.948 0.531,0.167 10 false IG 4.479,3.083 5.01,3.25 0.531,0.167 10 false GND 4.885,1.677 5.417,1.844 0.531,0.167 10 false 7 4.865,2.969 5.396,3.135 0.531,0.167 10 false 8 3.698,1.677 4.229,1.844 0.531,0.167 10 false 1 1.083,1.76 3.01,2.198 1.927,0.438 10 false from IGP NO. 3 Relay 0.802,3.333 1.333,3.5 0.531,0.167 10 false k7 3.292,3.563 5.063,4.198 1.771,0.635 10 false No. 1 Seat Cushion Climate Control Blower Assembly LH 0.813,4.365 2.823,4.646 2.01,0.281 10 false : LIN Communication Line 2.854,1.927 4.229,2.521 1.375,0.594 10 false S/HTR RL 3.292,3.365 3.823,3.531 0.531,0.167 10 false k4 0.781,3.552 2.74,4.146 1.958,0.594 10 false No. 1 Seatback Climate Control Blower Assembly LH 2.26,2.667 2.792,2.833 0.531,0.167 10 false 1 2.271,2.344 2.802,2.51 0.531,0.167 10 false 4 3.677,2.344 4.208,2.51 0.531,0.167 10 false 4 2.271,2.958 2.802,3.125 0.531,0.167 10 false 3 3.677,2.635 4.208,2.802 0.531,0.167 10 false 5 3.667,2.969 4.198,3.135 0.531,0.167 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

The climate control seat system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.

for 1GR-FE: Click herePower Source / Network>1GR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

for V35A-FTS: Click herePower Source / Network>V35A-FTS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

for F33A-FTV: Click herePower Source / Network>F33A-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SEAT BLOWER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Left Seat Blower Rear seat LH side seat blower operation OFF/ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Left Seat Blower
50004 450 24

Result:
Result Proceed to
Both No. 1 seat cushion seat blower and No. 1 seatback seat blower operate A
Only No. 1 seat cushion seat blower does not operate B
Only No. 1 seatback seat blower does not operate C
Both No. 1 seat cushion seat blower and No. 1 seatback seat blower do not operate D



A

2.REPLACE COOLER CONTROL SWITCH ASSEMBLY

B

REPLACE NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

C

4.CHECK HARNESS AND CONNECTOR (NO. 1 SEATBACK CLIMATE CONTROL BLOWER ASSEMBLY LH - NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH)

D

7.CHECK HARNESS AND CONNECTOR (NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BATTERY AND BODY GROUND)
2.REPLACE COOLER CONTROL SWITCH ASSEMBLY
a.

Replace the cooler control switch assembly with a new or known good one.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Rear Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK CLIMATE CONTROL SEAT OPERATION
3.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (COOLER CONTROL SWITCH ASSEMBLY WAS DEFECTIVE)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 1 SEATBACK CLIMATE CONTROL BLOWER ASSEMBLY LH - NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH)
a.

Disconnect the k7 No. 1 seatback climate control blower assembly LH connector.


b.

Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(k7,k4)Location & Routing

Click Connector(k7)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Back Climate Control Blower (Rear Seat LH)

Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)

k7-4 (GND) - k4-4 (BFB-) Always Below 1 Ω
k7-4 (GND) or k4-4 (BFB-) - Other terminals and body ground Always 10 kΩ or higher
k7-1 (IG) - k4-5 (CTB) Always Below 1 Ω
k7-1 (IG) or k4-5 (CTB) - Other terminals and body ground Always 10 kΩ or higher
k7-3 (BFB+) - k4-6 (BBS) Always Below 1 Ω
k7-3 (BFB+) or k4-6 (BBS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE NO. 1 SEATBACK CLIMATE CONTROL BLOWER ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NO. 1 SEATBACK CLIMATE CONTROL BLOWER ASSEMBLY LH
a.

Replace the No. 1 seatback climate control blower assembly LH with a new or known good one.

Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

6.CHECK CLIMATE CONTROL SEAT OPERATION
6.CHECK CLIMATE CONTROL SEAT OPERATION
a.

Check the climate control seat operation.

Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>OPERATION CHECK

OK:

The climate control seat operates normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 SEATBACK CLIMATE CONTROL BLOWER ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - BATTERY AND BODY GROUND)
a.

Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(k4)Location & Routing

Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)

k4-1 (IG) - Body ground Ignition switch ON 11 to 14 V
k4-1 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(k4)Location & Routing

Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)

k4-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the k4 No. 1 seat cushion climate control blower assembly LH connector.


b.

Disconnect the I31 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(k4,I31)Location & Routing

Click Connector(k4)Seat>Rear Seat Wire LH>LH Seat No. 1 Seat Cushion Climate Control Blower Assembly (Rear Seat LH)

Click Connector(I31)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Air Conditioning Amplifier Assembly

k4-7 (SIGN) - I31-22 (SV2L) Always Below 1 Ω
k4-7 (SIGN) or I31-22 (SV2L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
E409337C16
1.75,0.083 2.125,0.302 0.375,0.219 1.438,1.469 1.573,1.469 1.573,1.469 1.99,0.885 true 1.813,0.115 2.208,0.375 0.396,0.26 10 false I31 0.438,2.854 0.802,3.042 0.365,0.188 10 false GND 1.073,1.396 1.656,1.635 0.583,0.24 10 false SV2L 0.125,0.083 0.313,0.26 0.188,0.177 10 false *a
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Check for pulses according to the value(s) in the table below.

Measurement Condition
Item Content
Tester Connection I31-22 (SV2L) - Body ground
Tool Setting 1 V/DIV., 1 ms/DIV.
Vehicle Condition
·

Ignition switch ON

·

Rear left side refreshing seat switch (seat blower switch) on



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY