The combination meter assembly receives vehicle speed signals from the brake actuator assembly (No. 2 skid control ECU) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (No. 2 skid control ECU). The brake actuator assembly (No. 2 skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (No. 2 skid control ECU) detects vehicle speed signals based on pulses of the voltage.
Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (No. 2 skid control ECU) stores DTCs. Troubleshoot the electronically controlled brake system.
If the vehicle speed is outside the allowable range when tested, perform the operation check inspection.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the combination meter assembly is replaced, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
Before starting the following inspection, check tire size and tire air pressure.
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically controlled brake system DTCs are not output. | A |
| Electronically controlled brake system DTC is output. | B |
A
B
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Control Range | Diagnostic Note |
|---|---|---|
| Speedometer Operation (0km/h,0MPH) | Speedometer 0 km/h (0 mph) | - |
| Speedometer Operation (40km/h,40MPH) | Speedometer 40 km/h (40 mph) | The value displayed on the speedometer may deviate. Reference km/h: 40 → 42.0 to 46.0*1 40 → 40.7 to 42.7*2 |
| Speedometer Operation (80km/h,80MPH) | Speedometer 80 km/h (80 mph) | The value displayed on the speedometer may deviate. Reference km/h: 80 → 84.0 to 88.0*1 80 → 81.5 to 83.5*2 |
| Speedometer Operation (120km/h,120MPH) | Speedometer 120 km/h (120 mph) | The value displayed on the speedometer may deviate. Reference km/h: 120 → 125.0 to 130.0*1 120 → 122.2 to 124.2*2 |
| Speedometer Operation (160km/h,160MPH) | Speedometer 160 km/h (160 mph) | The value displayed on the speedometer may deviate. Reference km/h: 160 → 167.0 to 173.0*1 160 → 163.0 to 165.0*2 |
| Speedometer Operation (200km/h,200MPH) | Speedometer 200 km/h (200 mph) | The value displayed on the speedometer may deviate. Reference km/h: 200 → 208.0 to 215.0*1 200 → 203.7 to 205.7*2 |
*1: w/o Rear Occupant Detection Sensor
*2: w/ Rear Occupant Detection Sensor
| Tester Display |
|---|
| Speedometer Operation (0km/h,0MPH) |
| Tester Display |
|---|
| Speedometer Operation (40km/h,40MPH) |
| Tester Display |
|---|
| Speedometer Operation (80km/h,80MPH) |
| Tester Display |
|---|
| Speedometer Operation (120km/h,120MPH) |
| Tester Display |
|---|
| Speedometer Operation (160km/h,160MPH) |
| Tester Display |
|---|
| Speedometer Operation (200km/h,200MPH) |
Speedometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD:
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
NG