Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Oil Pressure Gauge Malfunction  


DESCRIPTION

The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.

WIRING DIAGRAM

for 1GR-FE:


E466463E01
2.313,1.406 2.667,1.573 0.354,0.167 10 false ECM 1.417,2.365 2.302,2.542 0.885,0.177 10 false C79 1.417,2.573 3.833,2.75 2.417,0.177 10 false Oil Pressure Sender Gauge Assembly 4.573,3.208 6.448,3.385 1.875,0.177 10 false Combination Meter Assembly 4.656,1.917 4.927,2.083 0.271,0.167 10 false 21 4.573,3.042 4.958,3.198 0.385,0.156 10 false I5 4.927,2.177 5.052,2.333 0.125,0.156 10 false S 2.417,1.917 2.542,2.083 0.125,0.167 10 false 1 2.198,2.052 2.323,2.208 0.125,0.156 10 false S 5.802,1.76 6.073,1.927 0.271,0.167 10 false OIL 0.885,3.26 2.573,3.469 1.688,0.208 10 false : CAN Communication Line


for V35A-FTS:


E407708E04
4.667,1.583 6.542,1.917 1.875,0.333 10 false Combination Meter Assembly 0.698,2.26 2.781,2.563 2.083,0.302 10 false : CAN Communication Line 1.677,1.604 3.323,2.042 1.646,0.438 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the ECM, refer to the Service Bulletin.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. (for 4.2 Inch Multi-information Display) A
CAN communication DTCs are not output. (for 7.0 Inch Multi-information Display) B
CAN communication DTCs are output. C



A

2.PERFORM ACTIVE TEST USING GTS

B

7.CHECK VEHICLE TYPE

C

2.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Oil Pressure Meter Operation (LOW) Oil pressure receiver gauge (Low) ON See [Display]
Oil Pressure Meter Operation (1/4) Oil pressure receiver gauge (1/4) ON See [Display]
Oil Pressure Meter Operation (1/2) Oil pressure receiver gauge (1/2) ON See [Display]
Oil Pressure Meter Operation (3/4) Oil pressure receiver gauge (3/4) ON See [Display]
Oil Pressure Meter Operation (HIGH) Oil pressure receiver gauge (High) ON See [Display]
Body Electrical > Combination Meter > Active Test
Tester Display
Oil Pressure Meter Operation (LOW)
50004 409 251
Body Electrical > Combination Meter > Active Test
Tester Display
Oil Pressure Meter Operation (1/4)
50004 409 252
Body Electrical > Combination Meter > Active Test
Tester Display
Oil Pressure Meter Operation (1/2)
50004 409 253
Body Electrical > Combination Meter > Active Test
Tester Display
Oil Pressure Meter Operation (3/4)
50004 409 254
Body Electrical > Combination Meter > Active Test
Tester Display
Oil Pressure Meter Operation (HIGH)
50004 409 255
OK:

Oil pressure gauge indication is normal.


i.
B611435C01
0.813,2.198 1.125,2.396 0.313,0.198 10 false *a 0.125,1.083 0.438,1.281 0.313,0.198 10 false *a 0.823,0.5 1.135,0.698 0.313,0.198 10 false *b 1.604,0.302 1.917,0.5 0.313,0.198 10 false *c 2.396,0.448 2.708,0.646 0.313,0.198 10 false *d 3.073,1.052 3.385,1.25 0.313,0.198 10 false *e
*a Oil Pressure Meter Operation (LOW)
*b Oil Pressure Meter Operation (1/4)
*c Oil Pressure Meter Operation (1/2)
*d Oil Pressure Meter Operation (3/4)
*e Oil Pressure Meter Operation (HIGH)


[Display]: Oil pressure gauge



Result:
Result Proceed to
OK (for 1GR-FE) A
OK (for V35A-FTS) B
OK (for F33A-FTV) C
NG D



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OIL PRESSURE SENDER GAUGE ASSEMBLY)

B

5.CHECK FOR DTC (SFI SYSTEM)

C

6.CHECK FOR DTC (ECD SYSTEM)

D

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OIL PRESSURE SENDER GAUGE ASSEMBLY)
a.

Disconnect the I5 combination meter assembly connector.


b.

Disconnect the C79 oil pressure sender gauge assembly connector.



Result:
Proceed to
OK
NG



OK

4.INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Temporarily replace the oil pressure sender gauge assembly with a new or normally functioning one.

Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.

Perform an operation check and check that the operation of the combination meter returns to normal.

OK:

Needle is as shown in illustration when engine is stopped.

Operation of combination meter returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

5.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

NG

6.CHECK FOR DTC (ECD SYSTEM)
a.

Check if ECD system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

NG

7.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for 1GR-FE A
for V35-FTS B
for F33A-FTV C



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OIL PRESSURE SENDER GAUGE ASSEMBLY)

B

10.CHECK FOR DTC (SFI SYSTEM)

C

12.CHECK FOR DTC (ECD SYSTEM)
8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - OIL PRESSURE SENDER GAUGE ASSEMBLY)
a.

Disconnect the I5 combination meter assembly connector.


b.

Disconnect the C79 oil pressure sender gauge assembly connector.



Result:
Proceed to
OK
NG



OK

9.INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Temporarily replace the oil pressure sender gauge assembly with a new or normally functioning one.

Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.

Perform an operation check and check that the operation of the combination meter returns to normal.

OK:

Needle is as shown in illustration when engine is stopped.

Operation of combination meter returns to normal.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

10.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (SFI SYSTEM)

NG

11.READ VALUE USING GTS (SFI SYSTEM)
a.

Using the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Oil Pressure Engine oil pressure Min.: 0 kPa, Max.: 5119.921 kPa
·

100 kPa or higher: 1500 rpm (engine oil temperature is 75 to 85°C [167 to 185°F])

·

200 kPa or higher: 2500 rpm (engine oil temperature is 75 to 85°C [167 to 185°F])


-
Powertrain > Engine > Data List
Tester Display
Engine Oil Pressure
50003 372 103
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

12.CHECK FOR DTC (ECD SYSTEM)
a.

Check if ECD system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Proceed to
OK
NG



OK

13.READ VALUE USING GTS (SFI SYSTEM)

NG

13.READ VALUE USING GTS (SFI SYSTEM)
a.

Using the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Oil Pressure Engine oil pressure Min.: 0 kPa, Max.: 5119.921 kPa
Idling (A/C off and shift lever in neutral):
·

Engine coolant temperature is 80 to 85 °C : 62 kPa or higher

·

Engine coolant temperature is 95 to 100 °C : 54 kPa or higher


3000 rpm (A/C off and shift lever in neutral):
·

Engine coolant temperature is 80 to 85 °C : 278 kPa or higher

·

Engine coolant temperature is 95 to 100 °C : 244 kPa or higher


-
Powertrain > Engine > Data List
Tester Display
Engine Oil Pressure
50003 372 103
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG