Home › Engine / Hybrid System › F33A-FTV (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2021.07
RM38G0E _51 Engine / Hybrid System _106330 F33A-FTV ENGINE MECHANICAL _0491798 REAR CRANKSHAFT OIL SEAL A

F33A-FTV ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A493552N02
3.219,4.781 4.094,4.958 0.875,0.177 3.177,4.729 4.146,5.01 0.969,0.281 1.573,3 1.75,3 1.75,3 1.896,2.5 true 6.063,5.135 6.063,4.49 true 3.406,2.281 4.281,1.865 4.281,1.865 4.646,1.865 true 1.563,2 1.885,1.083 1.885,1.083 2.146,1.083 true 3.667,3.563 3.844,3.563 3.844,3.563 3.99,3.063 true 2.646,2.188 2.802,1.771 2.802,1.771 3.063,1.771 true 4.104,4.875 4.281,4.875 4.281,4.875 4.531,4.417 true 6.375,0.229 6.813,0.229 true 5.99,5.167 6.323,5.573 0.333,0.406 18 false 4 5.031,1.74 5.365,2.146 0.333,0.406 18 false 2 2.656,0.948 2.99,1.354 0.333,0.406 18 false 1 2.469,0.99 2.802,1.396 0.333,0.406 10 false ● 3.5,3.49 3.833,3.896 0.333,0.406 10 false *1 3.125,1.688 3.458,2.094 0.333,0.406 10 false *2 1.406,2.927 1.74,3.333 0.333,0.406 10 false *3 4.646,4.302 4.979,4.708 0.333,0.406 10 false x 8 2.885,4.802 3.271,5.208 0.385,0.406 10 false ● ★ 3.26,4.802 4.25,5.094 0.99,0.292 8 false 182 (1856, 134) 5.896,0.104 6.49,0.625 0.594,0.521 18 false 3, 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR ENGINE OIL SEAL 11381A (Click here) - -
2 INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
3 INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY 32101 (Click here) - -
4 AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY - - - -
5 INSPECT FOR OIL LEAK - (Click here) - -

*1 REAR DRIVE PLATE SPACER *2 REAR CRANKSHAFT BALANCER WEIGHT
*3 NO. 1 CRANKSHAFT POSITION SENSOR PLATE - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part
★ Precoated part
V100135

MP grease
V100136

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent - -

PROCEDURE

Hide 11381A 1.INSTALL REAR ENGINE OIL SEAL

a.
A493553C01
5.677,0.719 6.438,0.719 true 3.958,1.063 4.188,1.063 true 3.958,1.563 4.188,1.563 true 0.448,0.031 0.729,0.385 0.281,0.354 18 false i 3.208,0.031 3.49,0.385 0.281,0.354 18 false ii 6.49,0.646 6.844,0.875 0.354,0.229 10 false SST 4.177,0.125 4.531,0.354 0.354,0.229 10 false *a 4.24,1 4.594,1.229 0.354,0.229 10 false *1 4.229,1.49 4.583,1.719 0.354,0.229 10 false *2
*1 Rear Engine Oil Seal *2 Rear Engine Oil Seal Retainer
*a 0 to 2.0 mm (0 to 0.0787 in.) - -


i.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Do not allow foreign matter to contact the lip of the rear engine oil seal.



ii.

Using SST and a hammer, tap in the rear engine oil seal to the rear engine oil seal retainer edge.

SST
09223-56010  

Oil Seal Protrusion Height:

0 to 2.0 mm (0 to 0.0787 in.)


NOTICE:
·

Do not tap the rear engine oil seal at an angle.

·

Keep the lip free of foreign matter.





Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A493554C04
4.167,2.823 4.344,2.823 4.344,2.823 4.667,2.542 true 4.813,3.083 4.99,3.083 4.99,3.083 5.313,2.802 true 5.167,3.615 5.344,3.615 5.344,3.615 5.667,3.333 true 6.01,3.792 6.188,3.792 6.188,3.792 6.51,3.51 true 0.708,1.083 0.823,1.198 0.823,1.198 1,1.198 true 2.594,3.021 2.594,2.781 true 5.844,3.719 6.115,3.906 0.271,0.188 10 false *1 5,3.542 5.26,3.823 0.26,0.281 10 false *2 4.646,3.01 4.958,3.24 0.313,0.229 10 false *3 3.99,2.75 4.313,3.063 0.323,0.313 10 false *4 0.469,0.052 1.458,0.344 0.99,0.292 18 false i, ii, iii 3.948,0.042 4.302,0.427 0.354,0.385 18 false iv 0.5,4 0.854,4.385 0.354,0.385 18 false v 3.906,3.99 4.177,4.292 0.271,0.302 18 true vi 6.844,0.813 7.115,1.135 0.271,0.323 10 false *a 5.292,4.208 5.396,4.375 0.104,0.167 10 true 1 5.531,5.385 5.635,5.552 0.104,0.167 10 true 2 5.958,4.698 6.063,4.865 0.104,0.167 10 true 4 4.885,4.948 4.99,5.115 0.104,0.167 10 true 3 5.698,4.313 5.802,4.479 0.104,0.167 10 true 7 5.135,5.302 5.24,5.469 0.104,0.167 10 true 8 5.885,5.156 5.99,5.323 0.104,0.167 10 true 6 4.948,4.5 5.052,4.667 0.104,0.167 10 true 5 1.031,1.115 1.208,1.292 0.177,0.177 10 true *b 2.51,3.021 2.688,3.198 0.177,0.177 10 true *c
*1 Rear Drive Plate Spacer *2 Drive Plate And Ring Gear Sub-assembly
*3 Rear Crankshaft Balancer Weight *4 No. 1 Crankshaft Position Sensor Plate
*a Automatic Transmission Assembly With Transfer Assembly Side *b Service Hole
*c Protrusion - -


i.

Align the service hole of the crankshaft pulley sub-assembly with the position as shown in the illustration.


ii.

Install a service bolt and fix the crankshaft pulley sub-assembly.

Service Bolt
Length 120 mm (4.72 in.) or more
Diameter 14 mm (0.551 in.)
Pitch 1.5
Thread Length 70 mm (2.76 in.) or more

HINT:

The crankshaft pulley sub-assembly is fixed by hooking a service bolt on the convex part of the timing chain cover sub-assembly.



iii.

Clean the 8 bolt holes.


iv.

Install the rear drive plate spacer, drive plate and ring gear sub-assembly, rear crankshaft balancer Weight and No. 1 crankshaft position aensor plate as shown in the illustration.

HINT:

As the rear drive plate spacer and No. 1 crankshaft position sensor plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



v.

Apply a few drops of adhesive to 2 or 3 threads at the tip of each of 8 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

After applying the adhesive, tighten the bolt right away.



vi.

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
182 N*m (1856 kgf*cm, 134 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate and ring gear sub-assembly installation bolts.

·

Handle the drive plate and ring gear sub-assembly installation bolts carefully. Do not scratch them or subject them to any shocks.

·

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.





Hide 32101 3.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER ASSEMBLY