Home › Engine / Hybrid System › F33A-FTV (LUBRICATION) › OIL PRESSURE SWITCH › from 2021.07
RM38G0E _51 Engine / Hybrid System _106335 F33A-FTV LUBRICATION _0491802 OIL PRESSURE SWITCH A

F33A-FTV LUBRICATION  OIL PRESSURE SWITCH  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A491403N02
4.396,4.135 5.094,4.313 0.698,0.177 3.99,5.281 4.688,5.458 0.698,0.177 4.073,4.198 4.385,4.198 false 4.521,4.99 4.99,4.99 false 2.271,4.802 2.375,4.26 2.375,4.26 2.635,4.26 false 1.135,4.146 1.24,3.604 1.24,3.604 1.5,3.604 false 6.365,0.208 6.833,0.208 false 3.667,5.365 3.979,5.365 false 5.656,4.073 5.938,4.427 0.281,0.354 18 false 1 5.063,4.844 5.344,5.198 0.281,0.354 18 false 2 5.458,4.135 5.698,4.323 0.24,0.188 10 false ★ 3.542,5.417 3.854,5.615 0.313,0.198 10 false x 5 2.073,5.26 2.385,5.458 0.313,0.198 10 false x 2 1.188,4.719 1.5,4.917 0.313,0.198 10 false x 2 1.563,3.542 1.875,3.74 0.313,0.198 10 false *2 2.698,4.188 3.01,4.385 0.313,0.198 10 false *1 4.427,4.146 5.198,4.354 0.771,0.208 8 false 15 (153, 11) 5.917,0.094 6.479,0.458 0.563,0.365 18 false 3, 4 4.031,5.292 4.802,5.5 0.771,0.208 8 false 29 (296, 21)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 OIL PRESSURE SENDER GAUGE ASSEMBLY 83520 (Click here) - -
2 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -
3 INSPECT ENGINE OIL LEVEL - (Click here) - -
4 INSPECT FOR OIL LEAK - (Click here) - -

*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
★ Precoated part - -

PROCEDURE

Hide 83520 1.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

a.
A491405C02
2.115,1.156 2.635,1.156 true 2.688,1.083 3,1.281 0.313,0.198 10 false *a 0.5,0.073 0.781,0.427 0.281,0.354 18 false i 3.802,0.063 4.083,0.417 0.281,0.354 18 false ii 1.969,2.083 2.25,2.438 0.281,0.354 18 false iii
*a Oil Inlet Port - -


i.

Apply adhesive to the shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:
·

Do not apply adhesive to the oil inlet port of the oil pressure sender gauge assembly.

·

Apply adhesive to the entire circumference of the thread.




ii.

Using a 27 mm deep socket wrench, install the oil pressure sender gauge assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine within 1 hour of installation.



iii.

Connect the oil pressure sender gauge assembly connector.



Hide 51410 2.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY