| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FUEL SENDER GAUGE ASSEMBLY | 83320 | - | - | - |
| 2 | FUEL TANK VENT TUBE ASSEMBLY (for RH Side) | 77010 | - | - | - |
| *1 | BUTYL TAPE | *2 | TUBE JOINT CLIP |
| *3 | NO. 1 FUEL TUBE CLAMP | *4 | GASKET |
| ● | Non-reusable part | - | - |
| *A | w/ Rear No. 2 Seat | - | - |
| *1 | NO. 4 REAR SIDE AIR DUCT | *2 | NO. 6 REAR SIDE AIR DUCT |
| *3 | REAR FLOOR SILENCER | *4 | FRONT FLOOR CARPET ASSEMBLY |
83320 1.INSTALL FUEL SENDER GAUGE ASSEMBLY
77010 2.INSTALL FUEL TANK VENT TUBE ASSEMBLY (for RH Side)
83320B 3.INSTALL NO. 2 FUEL SENDER GAUGE ASSEMBLY
77010 4.INSTALL FUEL TANK VENT TUBE ASSEMBLY (for LH Side)
| *a | Protrusion | *b | Notch |
Install a new gasket to the fuel tank sub-assembly.
Set the fuel tank vent tube assembly and align the protrusions of the fuel tank vent tube assembly with the notches in the fuel tank sub-assembly.
77144A 5.INSTALL FUEL PUMP GAUGE RETAINER (for LH Side)
| *a | SST (Plate) | *b | SST (Bolt) |
| *c | SST (Claw) | *d | Insertion Point |
| *e | SST (Handle) | *f | Triangle Mark (Fuel Pump Gauge Retainer) |
| *g | Triangle Mark (Fuel Tank Sub-assembly) | - | - |
While pressing down on the fuel tank vent tube assembly, temporarily install the fuel pump gauge retainer.
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
Install SST (handle) to SST (plate).
Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank sub-assembly to install the fuel tank vent tube assembly to the fuel tank sub-assembly.
Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank sub-assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
Make sure that the gasket does not come off.
77207B 6.CONNECT NO. 3 FUEL MAIN TUBE SUB-ASSEMBLY
Push the fuel tube joint of the No. 3 fuel main tube sub-assembly, and install the tube joint clip.
| *1 | Tube Joint Clip |
| *a | Nylon Tube |
| *b | Fuel Tube Joint |
| *c | O-ring |
| *d | Correct |
| *e | Incorrect |
Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
Check that the fuel tube joint is securely inserted to the end.
Check that the tube joint clip is on the collar of the fuel tube joint.
After installing the tube joint clip, check that the No. 3 fuel main tube sub-assembly is securely connected by pulling on it.
77026B 7.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
58325E 8.INSTALL REAR FLOOR SERVICE HOLE COVER (for LH Side)
Remove any remaining butyl tape from the rear floor service hole cover and body.
Install the rear floor service hole cover with new butyl tape.
Securely install the rear floor service hole cover.
Return the rear floor silencer and attach the 2 clips.
Install the No. 4 rear side air duct and No. 6 rear side air duct and attach the 2 clips.
Return the front floor carpet assembly and attach the 6 clips.
w/ Rear No. 2 Seat:
Attach the 4 clips.
67917C 9.INSTALL REAR DOOR SCUFF PLATE RH
67918D 10.INSTALL REAR DOOR SCUFF PLATE LH
71F95 11.INSTALL REAR NO. 4 SEAT PROTECTOR
71695Y 12.INSTALL REAR NO. 3 SEAT PROTECTOR
71695T 13.INSTALL REAR NO. 2 SEAT PROTECTOR
71695S 14.INSTALL REAR NO. 1 SEAT PROTECTOR
79959G 15.INSTALL NO. 2 SEAT NO. 1 LEG COVER RH (w/ Rear No. 2 Seat)
79959J 16.INSTALL NO. 2 SEAT NO. 1 LEG COVER LH (w/ Rear No. 2 Seat)
58417B 17.INSTALL REAR FLOOR BOARD REAR RH
58418H 18.INSTALL REAR FLOOR BOARD REAR LH
66310N 19.INSTALL ROPE HOOK ASSEMBLY
58410B 20.INSTALL DECK BOARD ASSEMBLY
66310N 21.INSTALL ROPE HOOK ASSEMBLY
22.INSTALL REAR NO. 1 SEAT ASSEMBLY
for LH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>INSTALLATION
for 60/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>INSTALLATION
for 40/20/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>INSTALLATION
77310A 23.INSTALL FUEL TANK CAP ASSEMBLY
24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
25.BLEED AIR FROM FUEL SYSTEM
26. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
27.INSPECT FOR FUEL LEAK