| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FRONT BUMPER BRACKET SUB-ASSEMBLY LH | 52016B | - | - | - |
| 2 | FRONT BUMPER BRACKET SUB-ASSEMBLY RH | 52015B | - | - | - |
| 3 | HEADLIGHT ASSEMBLY LH | - | - | - | - |
| 4 | HEADLIGHT ASSEMBLY RH | - | - | - | - |
| 5 | FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH | 53808D | - | - | - |
| 6 | FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP RH | 53807D | - | - | - |
| *A | w/ Bracket | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | w/ Winch | *B | w/o Winch |
| *C | w/ Intercooler | - | - |
|
Tightening torque for "major areas involving basic vehicle performance such as moving/turning/stopping" : N*m(kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| *A | w/o Garnish | *B | w/ TOYOTA Parking Assist-sensor System |
| *C | w/ Headlight Cleaner System | *D | w/o TOYOTA Parking Assist-sensor System, w/o Fog Light |
| *E | w/ TOYOTA Parking Assist-sensor System or w/ Fog Light or w/ Both | *F | w/o Dynamic Radar Cruise Control System |
| *G | w/ Dynamic Radar Cruise Control System | - | - |
| *1 | FRONT BUMPER COVER | *2 | NO. 4 ENGINE ROOM WIRE |
| ● | Non-reusable part | - | - |
| *A | w/ Extension Mounting Bracket | *B | w/ Winch |
| *C | w/ Garnish | *D | w/o Garnish |
| *E | w/ TOYOTA Parking Assist-sensor System | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 47 | FOG LIGHT COVER LH | 81482C | - | - | - |
| 48 | FOG LIGHT COVER RH | 81481E | - | - | - |
| 49 | FRONT BUMPER HOLE COVER LH | 52128B | - | - | - |
| 50 | FRONT BUMPER HOLE COVER RH | 52127D | - | - | - |
| 51 | FOG LIGHT BRACKET LH | 81482M | - | - | - |
| 52 | FOG LIGHT BRACKET RH | 81481R | - | - | - |
| 53 | CORNERING LIGHT ASSEMBLY LH | - | - | - | - |
| 54 | CORNERING LIGHT ASSEMBLY RH | - | - | - | - |
| 55 | FOG LIGHT ASSEMBLY LH | - | - | - | - |
| 56 | FOG LIGHT ASSEMBLY RH | - | - | - | - |
| 57 | FRONT BUMPER INNER BRACKET LH | 52149H | - | - | - |
| 58 | FRONT BUMPER INNER BRACKET RH | 52149G | - | - | - |
| *A | w/o Fog Light | *B | w/ Fog Light |
| *C | w/o Cornering Light | *D | w/ Cornering Light |
| *A | w/ Headlight Cleaner System | *B | w/ TOYOTA Parking Assist-sensor System |
| *C | w/o Dynamic Radar Cruise Control System | *D | w/ Dynamic Radar Cruise Control System |
| *E | w/o Garnish | *F | w/ Panoramic View Monitor System |
| *1 | NO. 1 HEADLIGHT CLEANER CLAMP | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
52016B 1.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY LH (w/ Bracket)
52015B 2.INSTALL FRONT BUMPER BRACKET SUB-ASSEMBLY RH (w/ Bracket)
3.INSTALL HEADLIGHT ASSEMBLY LH
4.INSTALL HEADLIGHT ASSEMBLY RH
53808D 5.INSTALL FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH
53807D 6.INSTALL FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP RH
52116A 7.INSTALL FRONT BUMPER SIDE SUPPORT LH
52115A 8.INSTALL FRONT BUMPER SIDE SUPPORT RH
52021 9.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (w/o Winch)
16550B 10.INSTALL NO. 2 INTERCOOLER COOLING RADIATOR ASSEMBLY (w/ Intercooler)
16550 11.INSTALL INTERCOOLER COOLING RADIATOR ASSEMBLY (w/ Intercooler)
165D1 12.INSTALL NO. 1 SUB-RADIATOR DUCT LH (w/ Intercooler)
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>RADIATOR>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>RADIATOR>INSTALLATION
165C1A 13.INSTALL NO. 1 SUB-RADIATOR DUCT RH (w/ Intercooler)
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>RADIATOR>INSTALLATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>RADIATOR>INSTALLATION
16595B 14.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Intercooler)
16593B 15.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Intercooler)
52618 16.INSTALL FRONT BUMPER LOWER ABSORBER (w/o Winch)
52521 17.INSTALL FRONT BUMPER CENTER UPPER RETAINER
52611 18.INSTALL FRONT BUMPER ENERGY ABSORBER (w/o Winch)
82090A 19.INSTALL EXTENSION WIRE ASSEMBLY (w/ Winch)
16595B 21.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Winch)
16593B 22.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Winch)
52421A 23.INSTALL FRONT BUMPER PAD
|
|
| Part | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
| Front Bumper Pad |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper pad and front bumper cover excessively.
| *a | Mark-off Line | - | - |
|
Installation area | - | - |
Clean the front bumper cover surface.
1. When reusing the front bumper cover, remove remaining double-sided tape from the front bumper cover.
2. Using a heat light, heat the front bumper cover surface.
3. Remove any remaining double-sided tape from the front bumper cover and wipe off any tape adhesive residue with cleaner.
4. Clean the installation area surface.
Installing the front bumper pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new front bumper cover surface.
Using a heat light, heat the front bumper cover and a new front bumper pad.
Install the 4 front bumper pads in the position shown in the illustration.
The application strength of the front bumper pad will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front bumper cover.
53111 24.INSTALL RADIATOR GRILLE
85361C 26.INSTALL WASHER BRACKET (w/ Headlight Cleaner System)
Use the same procedure described for No. 2 washer bracket.
53113B 27.INSTALL RADIATOR SIDE GRILLE LH
53112B 28.INSTALL RADIATOR SIDE GRILLE RH
Use the same procedure described for LH side.
89C48E 29.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System, w/o Garnish)
53113C 30.INSTALL LOWER RADIATOR GRILLE LH (w/o Garnish)
53112C 31.INSTALL LOWER RADIATOR GRILLE RH (w/o Garnish)
53101 32.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
33.INSTALL NO. 7 RADIATOR GRILLE MOULDING (w/ TOYOTA Parking Assist-sensor System or w/Fog Light or w/ Both)
75310A 34.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY
53039 35.INSTALL UPPER RADIATOR SEAL
36.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
82114 37.INSTALL NO. 4 ENGINE ROOM WIRE
w/o TOYOTA Parking Assist-sensor System, w/o Fog Light:
w/ TOYOTA Parking Assist-sensor System or w/o Fog Light or w/ Both:
| *A | w/ Fog Light | *B | w/ Panoramic View Monitor System |
76878C 38.INSTALL FRONT SPOILER SIDE PROTECTOR LH (w/ Garnish)
|
|
| Part | Temperature |
|---|---|
| Front Bumper Guard Assembly | 20 to 30°C (68 to 86°F) |
| Front Spoiler Side Protector LH |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front spoiler side protector LH and front bumper guard assembly excessively.
| *a | Mark-off Line | *b | Cutout |
Clean the front bumper guard assembly surface.
1. When reusing the front bumper guard assembly, remove remaining double-sided tape from the front bumper guard assembly.
2. Using a heat light, heat the front bumper guard assembly surface.
3. Remove any remaining double-sided tape from the front bumper guard assembly and wipe off any tape adhesive residue with cleaner.
4. Clean the installation area surface.
Installing the front spoiler side protector LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Also, clean a new front bumper guard assembly surface.
Primer application.
1. Apply primer to the front bumper guard assembly on the installation area of the front spoiler side protector LH using a brush or felt.
Replace the brush or felt if it is dirty or has become hardened.
Keep any painted surface free from primer.
If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
Do not touch surfaces to which primer has been applied until the front spoiler side protector LH has been attached.
2. Let the primer dry sufficiently.
Do not touch applied surfaces until the primer is dry.
10 minutes or more (at 23°C (73°F))
Using a heat light, heat the front bumper guard assembly and a new front spoiler side protector LH.
Install the front spoiler side protector LH in the position shown in the illustration.
The application strength of the front spoiler side protector LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
Apply pressure so that it does not lift up from the front bumper guard assembly.
76877E 39.INSTALL FRONT SPOILER SIDE PROTECTOR RH (w/ Garnish)
Use the same procedure described for LH side.
82223 40.INSTALL SWITCH WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Garnish)
89341L 41.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System, w/ Garnish)
52410B 42.INSTALL FRONT BUMPER GUARD ASSEMBLY (w/ Garnish)
C9715A 43.INSTALL NO. 1 WINCH WIRE (w/ Winch)
52049 44.INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY (w/ Winch)
75111 45.INSTALL FRONT LICENSE PLATE BRACKET (w/ Winch)
52114A 46.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Extension Mounting Bracket)
81482C 47.INSTALL FOG LIGHT COVER LH (w/ Fog Light)
81481E 48.INSTALL FOG LIGHT COVER RH (w/ Fog Light)
52128B 49.INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)
52127D 50.INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)
81482M 51.INSTALL FOG LIGHT BRACKET LH (w/ Fog Light)
81481R 52.INSTALL FOG LIGHT BRACKET RH (w/ Fog Light)
53.INSTALL CORNERING LIGHT ASSEMBLY LH (w/ Fog Light, w/ Cornering Light)
54.INSTALL CORNERING LIGHT ASSEMBLY RH (w/ Fog Light, w/ Cornering Light)
55.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light, w/o Cornering Light)
56.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light, w/o Cornering Light)
52149H 57.INSTALL FRONT BUMPER INNER BRACKET LH (w/ Fog Light)
52149G 58.INSTALL FRONT BUMPER INNER BRACKET RH (w/ Fog Light)
59.INSTALL COOLER THERMISTOR ASSEMBLY
86790B 60.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
88211B 61.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)
82824S 62.INSTALL WIRING HARNESS CONNECTOR (w/o Dynamic Radar Cruise Control System)
82667U 63.INSTALL NO. 32 CONNECTOR HOLDER (w/o Dynamic Radar Cruise Control System)
89C48D 64.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89341L 65.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System, w/o Garnish)
89341K 66.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
85208A 67.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A 68.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
85354 69.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)
85353 70.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)