Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P003312  Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery  P003314  Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Ground or Open  


DESCRIPTION

The air by-pass valve assembly is installed to the No. 2 turbocharger sub-assembly and is opened and closed based on operation commands from the ECM. It operates when switching from single turbo to twin turbo, and from twin turbo to single turbo.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P003312 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Battery Short circuit in air by-pass valve assembly circuit and power supply circuit.
(1 trip detection logic)
·

Short in air by-pass valve assembly circuit

·

Air by-pass valve assembly

·

ECM


Comes on SAE Code: P0035
P003314 Turbocharger / Supercharger Bypass Valve "A" Control Circuit Short to Ground or Open Open or short in air by-pass valve assembly circuit.
(1 trip detection logic)
·

Open or short in air by-pass valve assembly circuit

·

Air by-pass valve assembly

·

ECM


Comes on SAE Code: P0034

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P003312
P003314
Perform the Active Test "Activate the Air Bypass Valve" for 5 seconds or more.

WIRING DIAGRAM

A492900E01
0.646,4.01 1.323,4.26 0.677,0.25 10 false Battery 0.427,3.333 1.49,3.625 1.063,0.292 10 false SUB R/B NO. 1 3.448,1.146 4.125,1.396 0.677,0.25 10 false EFI NO. 1 2.344,2.833 3.042,3.042 0.698,0.208 10 false EFI NO. 2 1.302,2.406 1.958,2.802 0.656,0.396 10 false EFI MAIN NO. 1 2.906,3.042 3.99,3.323 1.083,0.281 10 false EFI MAIN NO. 1 1.063,1.375 2.24,1.635 1.177,0.26 10 false C160 1.063,1.531 3.5,1.885 2.438,0.354 10 false Air By-pass Valve Assembly 5.854,0.396 6.406,0.615 0.552,0.219 10 false ABV 5.844,2.708 6.396,2.927 0.552,0.219 10 false MREL 5.479,2.677 5.865,2.948 0.385,0.271 10 false B70 5.427,0.49 5.969,0.729 0.542,0.24 10 false C139 5.531,2.438 5.917,2.708 0.385,0.271 10 false 3 3.083,0.375 3.26,0.604 0.177,0.229 10 false 1 3.104,0.885 3.281,1.115 0.177,0.229 10 false 2 5.542,0.271 5.719,0.5 0.177,0.229 10 false 7 2.698,0.385 3.25,0.604 0.552,0.219 10 false ABV 2.792,0.896 3.073,1.125 0.281,0.229 10 false +B 6.208,3.344 6.875,3.635 0.667,0.292 10 false ECM 3.719,2.146 3.896,2.375 0.177,0.229 10 false 5 2.927,2.125 3.104,2.354 0.177,0.229 10 false 3 3.729,2.583 3.906,2.813 0.177,0.229 10 false 1 2.917,2.563 3.094,2.792 0.177,0.229 10 false 2 3.833,0.875 4.01,1.104 0.177,0.229 10 false 1 3.427,0.865 3.604,1.094 0.177,0.229 10 false 2 0.49,2.396 1.552,2.688 1.063,0.292 10 false R/B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR BY-PASS VALVE ASSEMBLY

OK

2.CHECK HARNESS AND CONNECTOR (CHECK VOLTAGE)

NG

9.REPLACE AIR BY-PASS VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (CHECK VOLTAGE)
a.

Disconnect the air by-pass valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C160)Location & Routing

Click Connector(C160)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly

C160-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)
a.

Disconnect the air by-pass valve assembly connector.


b.

Disconnect the ECM connector.




OK

4.CLEAR DTC

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312 OR P003314)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P003312 OR P003314)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P003312 or P003314.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P003312 or P003314 is output)
B




A

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
7.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the air by-pass valve assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the No. 3 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C160)Location & Routing

Click Connector(C160)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly

C160-2 (+B) - EFI MAIN NO. 1 relay terminal 5 Always Below 1 Ω
C160-2 (+B) or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
9.REPLACE AIR BY-PASS VALVE ASSEMBLY

NEXT

4.CLEAR DTC