The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.
When the throttle valve is fully closed, a voltage of approximately 0.4 to 1.0 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.6 to 4.2 V when the throttle valve is fully opened.
The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P012012 | Throttle/Pedal Position Sensor/Switch "A" Circuit Short to Battery | Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds. (1 trip detection logic) |
·
Throttle position sensor
·
Open in EVLU circuit
·
VCVL and VLU circuits are short circuited
·
ECM |
Comes on | SAE Code: P0123 |
| P012014 | Throttle/Pedal Position Sensor/Switch "A" Circuit Short to Ground or Open | Throttle position sensor output (VLU) is below 0.2 V for 3 seconds. (1 trip detection logic) |
·
Throttle position sensor
·
Open or short in VLU circuit
·
Open in VCVL circuit.
·
ECM |
Comes on | SAE Code: P0122 |
If DTC P012012 and/or P012014 is stored, the following symptoms may appear:
- Intake booming noise
- Black smoke
- Lack of power
- Vibration at engine stop
- Turbo overspeed, turbo damage
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P012012 P012014 |
Ignition switch ON for 3 seconds or more |
When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C177,C138)Location & Routingewd_type=routing;type=c,c;code=C177,C138 |
||
| C177-2 (VC) - C138-116 (VCVL) | Always | Below 1 Ω |
| C177-1 (VTA) - C138-69 (VLU) | Always | Below 1 Ω |
| C177-4 (E2) - C138-115 (EVLU) | Always | Below 1 Ω |
| C177-2 (VC) or C138-116 (VCVL) - Body ground and other terminals | Always | 10 kΩ or higher |
| C177-1 (VTA) or C138-69 (VLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| C177-4 (E2) or C138-115 (EVLU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C177)Location & Routingewd_type=routing;type=c;code=C177 |
||
| C177-2 (VC) - C177-4 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle body assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C177)Location & Routingewd_type=routing;type=c;code=C177 |
||
| C177-2 (VC) - C177-1 (VTA) | Ignition switch off | No short or no open circuit |
| C177-1 (VTA) - C177-4 (E2) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the diesel throttle body assembly.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT