Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery Conditions (a) and (b) continue for 5 seconds or more:

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 4.78 V or higher.


(1 trip detection logic)
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on SAE Code: P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open Conditions (a) and (b) continue for 5 seconds or more:

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 0.23 V or less.


(1 trip detection logic)
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on SAE Code: P0522

Related Data List
DTC No. Data List
P052012
P052014
Engine Oil Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052012
P052014
Idling for 5 seconds or more

WIRING DIAGRAM

A478140E04
1.021,1.719 1.552,1.927 0.531,0.208 10 false POUT 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.094,2.5 1.625,2.708 0.531,0.208 10 false GND 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPE 4.406,0.938 4.938,1.146 0.531,0.208 10 false 119 4.417,2.396 4.948,2.604 0.531,0.208 10 false 120 4.469,1.615 5,1.823 0.531,0.208 10 false 74 4.885,2.125 5.417,2.333 0.531,0.208 10 false 200 kΩ 4.75,2.396 5.281,2.604 0.531,0.208 10 false EPEO 4.75,1.625 5.281,1.833 0.531,0.208 10 false PEO 5.604,3.26 6.135,3.469 0.531,0.208 10 false ECM 5.604,3.104 6.135,3.313 0.531,0.208 10 false C138 0.24,2.896 0.771,3.104 0.531,0.208 10 false C168 0.24,3.063 2.948,3.313 2.708,0.25 10 false Oil Pressure Sender Gauge Assembly 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.51,1.615 2.042,1.823 0.531,0.208 10 false 2 1.521,2.396 2.052,2.604 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
a.

Disconnect the oil pressure sender gauge assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C168,C138)Location & Routing

Click Connector(C168)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Pressure Sender Gage Assembly

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C168-3 (VC) - C138-119 (VCPE) Always Below 1 Ω
C168-2 (POUT) - C138-74 (PEO) Always Below 1 Ω
C168-1 (E2) - C138-120 (EPEO) Always Below 1 Ω
C168-3 (VC) or C138-119 (VCPE) - Body ground and other terminals Always 10 kΩ or higher
C168-2 (POUT) or C138-74 (PEO) - Body ground and other terminals Always 10 kΩ or higher
C168-1 (E2) or C138-120 (EPEO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the oil pressure sender gauge assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C168)Location & Routing

Click Connector(C168)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Pressure Sender Gage Assembly

C168-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C168-2 (POUT) - Body ground Ignition switch ON Below 0.1 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C168)Location & Routing

Click Connector(C168)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Oil Pressure Sender Gage Assembly

C168-2 (POUT) - C168-1 (GND) Ignition switch off No short or no open circuit
C168-1 (GND) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK IF DTC OUTPUT RECURS (DTC P052012 OR P052014)
4.CHECK IF DTC OUTPUT RECURS (DTC P052012 OR P052014)
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine and idle it for 5 second or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P052012 or P052014 is output A
DTCs are not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


c.

Start the engine and idle it for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED