The fan speed sensor is provided inside the fluid coupling assembly and outputs 6 signals per fan rotation.
The ECM detects the fan speed from the pulse width of fan speed sensor signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P052631 | Fan Speed Sensor Circuit No Signal No Signal | When the engine is running (at 600 rpm or higher) and the fan control solenoid drive duty ratio is 10% or more, the fan speed sensor signal is not input for 10 seconds or more (1 trip detection logic) |
·
Fan speed sensor (fluid coupling assembly)
·
Wire harness or connector
·
ECM |
Does not come on | SAE Code: P0528 |
When the engine is running (at 600 rpm or higher) and the fan control solenoid drive duty ratio is 10% or more, the ECM stores a DTC if a fan speed sensor signal is not input.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P052631 | Start the engine and wait for at 2 minutes or more. |
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the fan speed sensor (fluid coupling assembly) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C165)Location & Routingewd_type=routing;type=c;code=C165 |
||
| C165-4 (VCFC) - C165-6 (E1FC) | Ignition switch ON | 4.5 to 5.5 V |
| C165-5 (NCFC) - C165-6 (E1FC) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P052631 is output | B |
A
B
Disconnect the fan speed sensor (fluid coupling assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C165,C138)Location & Routingewd_type=routing;type=c,c;code=C165,C138 |
||
| C165-4 (VCFC) - C138-96 (VCF) | Always | Below 1 Ω |
| C165-5 (NCFC) - C138-73 (NCF) | Always | Below 1 Ω |
| C165-6 (E1FC) - C138-97 (ECF) | Always | Below 1 Ω |
| C165-4 (VCFC) or C138-96 (VCF) - Body ground and other terminals | Always | 10 kΩ or higher |
| C165-6 (E1FC) or C138-97 (ECF) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG