Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P12AC12  Exhaust Control Valve Circuit Short to Battery  P12AC14  Exhaust Control Valve Circuit Short to Ground or Open  


DESCRIPTION

The No. 1 vacuum switching valve assembly (for exhaust control valve) is controlled by the ECM, and the opening and closing of the exhaust control valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P12AC12 Exhaust Control Valve Circuit Short to Battery Open or short in the No. 1 vacuum switching valve assembly (for exhaust control valve) for 3 seconds.
(1 trip detection logic)
·

Open or short in No. 1 vacuum switching valve assembly (for exhaust control valve) circuit

·

No. 1 vacuum switching valve assembly (for exhaust control valve)

·

ECM


Comes on SAE Code: P12AF
P12AC14 Exhaust Control Valve Circuit Short to Ground or Open Open or short in the No. 1 vacuum switching valve assembly (for exhaust control valve) for 3 seconds.
(1 trip detection logic)
·

Open or short in No. 1 vacuum switching valve assembly (for exhaust control valve) circuit

·

No. 1 vacuum switching valve assembly (for exhaust control valve)

·

ECM


Comes on SAE Code: P12AE

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P12AC12
P12AC14
Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A492900E03
0.615,4.031 1.292,4.281 0.677,0.25 10 false Battery 0.417,3.344 1.479,3.635 1.063,0.292 10 false SUB R/B NO. 1 3.448,1.146 4.125,1.396 0.677,0.25 10 false EFI NO. 1 2.313,2.833 3.01,3.042 0.698,0.208 10 false EFI NO. 2 1.146,2.396 2.24,2.677 1.094,0.281 10 false EFI MAIN NO. 1 2.906,3.042 3.99,3.323 1.083,0.281 10 false EFI MAIN NO. 1 1.188,1.375 2.365,1.635 1.177,0.26 10 false C164 1.188,1.521 3.75,2.281 2.563,0.76 10 false No. 1 Vacuum Switching Valve Assembly (for Exhaust Control Valve) 5.854,0.365 6.406,0.583 0.552,0.219 10 false ECV 5.844,2.677 6.396,2.896 0.552,0.219 10 false MREL 5.458,2.667 5.844,2.938 0.385,0.271 10 false B70 5.427,0.469 5.969,0.708 0.542,0.24 10 false C138 5.531,2.438 5.917,2.708 0.385,0.271 10 false 3 3.104,0.865 3.281,1.094 0.177,0.229 10 false 1 3.083,0.375 3.26,0.604 0.177,0.229 10 false 2 5.5,0.271 5.677,0.5 0.177,0.229 10 false 45 2.677,0.385 3.229,0.604 0.552,0.219 10 false ACM 2.802,0.875 3.083,1.104 0.281,0.229 10 false +B 6.229,3.292 6.688,3.594 0.458,0.302 10 false ECM 3.719,2.146 3.896,2.375 0.177,0.229 10 false 5 2.927,2.125 3.104,2.354 0.177,0.229 10 false 3 3.729,2.552 3.906,2.781 0.177,0.229 10 false 1 2.917,2.563 3.094,2.792 0.177,0.229 10 false 2 3.833,0.875 4.01,1.104 0.177,0.229 10 false 1 3.427,0.865 3.604,1.094 0.177,0.229 10 false 2 0.448,2.396 1.51,2.688 1.063,0.292 10 false R/B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)
a.

Inspect the No. 1 vacuum switching valve assembly (for exhaust control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) (POWER SOURCE CIRCUIT)

NG

8.REPLACE NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)
2.CHECK NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) (POWER SOURCE CIRCUIT)
a.

Disconnect the No. 1 vacuum switching valve assembly (for exhaust control valve) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C164)Location & Routing

Click Connector(C164)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Duty Vacuum Switching Valve

C164-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) - EFI MAIN NO. 1 RELAY)
3.CHECK HARNESS AND CONNECTOR (NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) - ECM)
a.

Disconnect the No. 1 vacuum switching valve assembly (for exhaust control valve) connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE) - EFI MAIN NO. 1 RELAY)
a.

Disconnect the No. 1 vacuum switching valve assembly (for exhaust control valve) connector.


b.

Remove the EFI MAIN NO. 1 relay from the No. 3 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C164)Location & Routing

Click Connector(C164)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Duty Vacuum Switching Valve

C164-1 (+B) - EFI MAIN NO. 1 relay terminal 5 Always Below 1 Ω
C164-1 (+B) or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the No. 1 vacuum switching valve assembly (for exhaust control valve) connector is not 11 to 14 V, repair or replace the harness and connector between the No. 1 vacuum switching valve assembly (for exhaust control valve) and instrument panel junction block assembly.



Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch to ON and wait for 3 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)
a.

Replace the No. 1 vacuum switching valve assembly (for exhaust control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED