The i-ART injector detects the fuel temperature from the sensors built into each injector assembly.
The fuel temperature detected inside the injector assembly is sent to the ECM as feedback through the communication line.
The ECM determines that there is a malfunction when the difference in the temperature data (voltage value) received from the injector assemblies via INJ communication exceeds a certain value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P13C013 | Fuel Temperature Sensor #1 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13C3 |
| P13C513 | Fuel Temperature Sensor #2 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13C8 |
| P13CA13 | Fuel Temperature Sensor #3 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13CD |
| P13D013 | Fuel Temperature Sensor #4 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13D3 |
| P13D513 | Fuel Temperature Sensor #5 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13D8 |
| P13DA13 | Fuel Temperature Sensor #6 Circuit Open | The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more. (1 trip detection logic) |
·
VIJ circuit malfunction
·
Fuel temperature sensor (built into injector assembly)
·
Harness or connector |
Comes on | SAE Code: P13DD |
| DTC No. | Data List |
|---|---|
| P13C013 P13C513 P13CA13 P13D013 P13D513 P13DA13 |
·
Fuel Temperature #1
·
Fuel Temperature #2
·
Fuel Temperature #3
·
Fuel Temperature #4
·
Fuel Temperature #5
·
Fuel Temperature #6 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P13C013 P13C513 P13CA13 P13D013 P13D513 P13DA13 |
Ignition switch ON for 8 second or more |
Refer to DTC P13A011.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P13A011
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs
| Result | Proceed to |
|---|---|
| "Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output*1 | A |
| "Fuel pressure sensor circuit DTC" and "Fuel temperature sensor circuit DTC" are output*2 | B |
| Only DTCs related to the "Fuel temperature sensor circuit DTC" are output*3 | C |
*1: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTCs:
Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511, P13E515.
Injector Internal EEPROM Malfunction circuit: P168A00, P168A44, P168A46, P168B00, P168B44, P168B46, P168C00, P168C44, P168C46, P168D00, P168D44, P168D46, P168E00, P168E44, P168E46, P168F00, P168F44, P168F46.
*2: Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511, P13E515.
Fuel temperature sensor circuit DTC: P13C013, P13C513, P13CA13, P13D013, P13D513, P13DA13.
*3: Fuel temperature sensor circuit DTC: P13C013, P13C513, P13CA13, P13D013, P13D513, P13DA13.
A
B
C
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C139,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=C117,C139,C118,C119,C120,C121,C122 |
||
| C117-2 (VIJ1) - C139-52 (VIJ1) | Always | Below 1 Ω |
| C117-1 (EIJ1) - C139-51 (EIJ1) | Always | Below 1 Ω |
| C118-2 (VIJ2) - C139-42 (VIJ2) | Always | Below 1 Ω |
| C118-1 (EIJ2) - C139-41 (EIJ2) | Always | Below 1 Ω |
| C119-2 (VIJ3) - C139-32 (VIJ3) | Always | Below 1 Ω |
| C119-1 (EIJ3) - C139-31 (EIJ3) | Always | Below 1 Ω |
| C120-2 (VIJ4) - C139-49 (VIJ4) | Always | Below 1 Ω |
| C120-1 (EIJ4) - C139-48 (EIJ4) | Always | Below 1 Ω |
| C121-2 (VIJ5) - C139-39 (VIJ5) | Always | Below 1 Ω |
| C121-1 (EIJ5) - C139-38 (EIJ5) | Always | Below 1 Ω |
| C122-2 (VIJ6) - C139-29 (VIJ6) | Always | Below 1 Ω |
| C122-1 (EIJ6) - C139-28 (EIJ6) | Always | Below 1 Ω |
| C117-2 (VIJ1) or C139-52 (VIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C117-1 (EIJ1) or C139-51 (EIJ1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-2 (VIJ2) or C139-42 (VIJ2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-1 (EIJ2) or C139-41 (EIJ2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-2 (VIJ3) or C139-32 (VIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-1 (EIJ3) or C139-31 (EIJ3) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-2 (VIJ4) or C139-49 (VIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-1 (EIJ4) or C139-48 (EIJ4) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-2 (VIJ5) or C139-39 (VIJ5) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-1 (EIJ5) or C139-38 (EIJ5) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-2 (VIJ6) or C139-29 (VIJ6) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-1 (EIJ6) or C139-28 (EIJ6) - Body ground and other terminals | Always | 10 kΩ or higher |
Reconnect the injector assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=C117,C118,C119,C120,C121,C122 |
||
| C117-2 (VIJ1) - C117-1 (EIJ1) | Ignition switch ON | 4.5 to 5.5 V |
| C118-2 (VIJ2) - C118-1 (EIJ2) | Ignition switch ON | 4.5 to 5.5 V |
| C119-2 (VIJ3) - C119-1 (EIJ3) | Ignition switch ON | 4.5 to 5.5 V |
| C120-2 (VIJ4) - C120-1 (EIJ4) | Ignition switch ON | 4.5 to 5.5 V |
| C121-2 (VIJ5) - C121-1 (EIJ5) | Ignition switch ON | 4.5 to 5.5 V |
| C122-2 (VIJ6) - C122-1 (EIJ6) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 8 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT