Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P25F812  Turbocharger/Supercharger Bypass Valve "C" Control Circuit High Circuit Short to Battery  P25F814  Turbocharger/Supercharger Bypass Valve "C" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The No. 2 vacuum switching valve assembly (for intake air control valve) is controlled by the ECM, and the opening and closing of the air control valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P25F812 Turbocharger/Supercharger Bypass Valve "C" Control Circuit High Circuit Short to Battery Open or short in the No. 2 vacuum switching valve assembly (for intake air control valve) for 3 seconds.
(1 trip detection logic)
·

Open or short in No. 2 vacuum switching valve assembly (for intake air control valve) circuit

·

No. 2 vacuum switching valve assembly (for intake air control valve)

·

ECM


Comes on SAE Code: P25FA
P25F814 Turbocharger/Supercharger Bypass Valve "C" Control Circuit Low Circuit Short to Ground or Open Open or short in the No. 2 vacuum switching valve assembly (for intake air control valve) for 3 seconds.
(1 trip detection logic)
·

Open or short in No. 2 vacuum switching valve assembly (for intake air control valve) circuit

·

No. 2 vacuum switching valve assembly (for intake air control valve)

·

ECM


Comes on SAE Code: P25F9

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P25F812
P25F814
Ignition switch ON for 3 seconds or more

WIRING DIAGRAM

A492900E04
0.604,4.042 1.281,4.292 0.677,0.25 10 false Battery 0.427,3.354 1.49,3.646 1.063,0.292 10 false SUB R/B NO. 1 3.396,1.146 4.073,1.396 0.677,0.25 10 false EFI NO. 1 2.333,2.833 3.031,3.042 0.698,0.208 10 false EFI NO. 2 1.135,2.396 2.229,2.677 1.094,0.281 10 false EFI MAIN NO. 1 2.854,3.042 3.938,3.323 1.083,0.281 10 false EFI MAIN NO. 1 1.448,1.354 2.625,1.615 1.177,0.26 10 false C115 1.427,1.521 3.969,2.333 2.542,0.813 10 false No. 2 Vacuum Switching Valve Assembly (for Intake Air Control Valve) 5.854,0.396 6.406,0.615 0.552,0.219 10 false ACV 5.844,2.708 6.396,2.927 0.552,0.219 10 false MREL 5.458,2.667 5.844,2.938 0.385,0.271 10 false B70 5.427,0.469 5.969,0.708 0.542,0.24 10 false C138 5.531,2.438 5.917,2.708 0.385,0.271 10 false 3 3.083,0.375 3.26,0.604 0.177,0.229 10 false 2 3.104,0.885 3.281,1.115 0.177,0.229 10 false 1 5.542,0.271 5.719,0.5 0.177,0.229 10 false 49 2.688,0.385 3.24,0.604 0.552,0.219 10 false AIV1 2.792,0.896 3.073,1.125 0.281,0.229 10 false +B 6.188,3.292 6.615,3.563 0.427,0.271 10 false ECM 3.719,2.146 3.896,2.375 0.177,0.229 10 false 5 2.927,2.125 3.104,2.354 0.177,0.229 10 false 3 3.729,2.552 3.906,2.781 0.177,0.229 10 false 1 2.917,2.563 3.094,2.792 0.177,0.229 10 false 2 3.833,0.875 4.01,1.104 0.177,0.229 10 false 1 3.427,0.865 3.604,1.094 0.177,0.229 10 false 2 0.427,2.396 1.49,2.688 1.063,0.292 10 false R/B NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)
a.

Inspect the No. 2 vacuum switching valve assembly (for intake air control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE) (POWER SOURCE CIRCUIT)

NG

7.REPLACE NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)
2.CHECK NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE) (POWER SOURCE CIRCUIT)
a.

Disconnect the No. 2 vacuum switching valve assembly (for intake air control valve) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C115)Location & Routing

Click Connector(C115)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Air Control Valve Assembly

C115-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE) - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE) - ECM)
a.

Disconnect the No. 2 vacuum switching valve assembly (for intake air control valve) connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the No. 2 vacuum switching valve assembly (for intake air control valve) connector is not 11 to 14 V, repair or replace the harness and connector between the No. 2 vacuum switching valve assembly (for intake air control valve) and instrument panel junction block assembly.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch to ON and wait for 3 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)
a.

Replace the No. 2 vacuum switching valve assembly (for intake air control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED