Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (w/o Emergency Call Service) › from 2022.11
RM38G0E _56 Audio / Visual / Telematics _100608 TELEMATICS _0562784 TELEMATICS SYSTEM(w/o Emergency Call Service) J

TELEMATICS  TELEMATICS SYSTEM(w/o Emergency Call Service)  Remote Engine Starter does not Operate  


WIRING DIAGRAM

E364889E26
1.563,0.865 2.052,1.073 0.49,0.208 10 false SLPD 5.208,0.875 5.604,1.073 0.396,0.198 10 false SLP 2.063,0.771 2.344,0.979 0.281,0.208 10 false 30 4.917,0.76 5.208,0.969 0.292,0.208 10 false 11 5.156,1.594 5.531,1.792 0.375,0.198 10 false I39 5.156,1.75 6.969,2.115 1.813,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.219,1.604 1.594,1.792 0.375,0.188 10 false I55 1.219,1.76 3,2.146 1.781,0.385 10 false Telephone Transceiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION


PROCEDURE

1.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check that the engine can be started by pressing the ignition switch.


Result:
Result Proceed to
Engine can be started. A
Engine cannot be started. B



A

2.REGISTRATION

B

2.REGISTRATION
HINT:
If registration is not performed after replacing any of the following parts, the remote engine start and stop will not be available.
·

Certification ECU (smart key ECU assembly)

·

Telephone transceiver assembly




b.

Check if the problem symptom recurs.


Result:
Result Proceed to
System does not return to normal. A
System returns to normal. B



A

3.CHECK DTC OUTPUT

B

END (COMMUNICATION ID REGISTRATION WAS NOT PERFORMED)

3.CHECK DTC OUTPUT
a.

Clear the DTCs.

Body Electrical > Power Source Control > Clear DTCs
50002 454

b.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output. A
DTC B228562 is output. B



A

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

B

4.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I55)Location & Routing

Click Connector(I55)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Telematics Transceiver Assembly

I55-30 (SLPD) - Body ground Steering locked 11 to 14 V
Steering unlocked 1.5 V or less


HINT:

The steering locks when any door is opened with the shift lever in P and the ignition switch off. The steering unlocks when the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the I55 telephone transceiver assembly connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR